In CMSIS 5.9.0, the compiler headers define `__VECTOR_TABLE`, which will be
substituted with its corresponding value (e.g., `__Vectors` for gcc).
However, the linker script in this port can't include compiler headers when
it's processed, so `__VECTOR_TABLE` is used as the literal variable name,
which results in an undefined linker error.
To fix this, the two possible values of `__VECTOR_TABLE` are both defined
in the linker script.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Minor change to remove support for using numeric IDs for machine.Pin. This
was previously based on the index of the pin in the board csv, but this is
different (and incompatible) with other ports.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
All ports now use `--board-csv`, `--prefix`, `--output-souce`,
`--output-header` and no longer write to stdout. This matches the esp32
implementation.
Ports that have an AF input use `--af-csv` (to match `--board-csv`).
Any additional output files are now prefixed with `output-` (e.g.
`--output-af-const`).
Default arguments are removed (all makefiles should always specify all
arguments, using default values is likely an error).
Replaced the `af-defs-cmp-strings` and `hdr-obj-decls` args for stm32 with
just `mboot-mode`. Previously they were set on the regular build, now the
logic is reversed so mboot sets it.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The machine_i2c_type, machine_spi_type and machine_timer_type symbols are
already declared in extmod/modmachine.h and should not be declared anywhere
else.
Also move declarations of machine_pin_type and machine_rtc_type to the
common header in extmod.
Signed-off-by: Damien George <damien@micropython.org>
Commit 552b0bbe12 did not define
MICROPY_PY_MACHINE_SDCARD properly, and thus building the firmware failed.
Signed-off-by: robert-hh <robert@hammelrath.com>
There is a single UART clock for all devices, so switching it for one will
affect all devices used at that time. This commit fixes that issue by
keeping the clock at a fixed value.
This fixed clock still supports the common baud rates between 300 and
921600 baud.
Signed-off-by: robert-hh <robert@hammelrath.com>
This is option is no longer needed as a Makefile option as the USDHC driver
is enabled for all supported series.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
At the Adafruit Metro M7 the pin GPIO_AD_13 is used for JTAG. Therefore
it is not configured for RTS at UART 2 and 3.
Signed-off-by: robert-hh <robert@hammelrath.com>
This commit:
- Finds a common set of board feature tags and maps existing features to
that reduced set.
- Removes some less-useful board feature tags.
- Ensures all MCUs are specified correctly.
- Ensures all boards have a vendor (and fixes some vendor names).
This is to make the downloads page show a less intimidating set of filters.
Work done in conjunction with Matt Trentini <matt.trentini@gmail.com>.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The asyncio module now has much better CPython compatibility and
deserves to be just called "asyncio".
This will avoid people having to write `from uasyncio import asyncio`.
Renames all files, and updates port manifests to use the new path. Also
renames the built-in _uasyncio to _asyncio.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit is necessary to make MicroPython work on this eval kit out of
the box, as the eval kit ships with the HyperFlash physically disconnected
from the bus (refer to the schematics or the user guide) and the QSPI
connected instead, but the fuses/board/pins are configured to boot from
internal flash (on FlexSPI2).
Note that enabling the HyperFlash is not trivial, as it requires soldering
and desoldering of many small footprint resistors and changing fuses.
This provides a standard interface to setting the global networking config
for all interfaces and interface types.
For ports that already use either a static hostname (mimxrt, rp2) they will
now use the configured value. The default is configured by the port
(or optionally the board).
For interfaces that previously supported .config(hostname), this is still
supported but now implemented using the global network.hostname.
Similarly, pyb.country and rp2.country are now deprecated, but the methods
still exist (and forward to network.hostname).
Because ESP32/ESP8266 do not use extmod/modnetwork.c they are not affected
by this commit.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This will ensure that any board with networking support gets:
- webrepl
- mip
- urequests
- ntptime
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The RT1176 has two cores, but the actual firmware supports only the CM7.
There are currently no good plans on how to use the CM4.
The actual MIMXRT1170_EVK board is on par with the existing MIMXRT boards,
with the following extensions:
- Use 64 MB RAM for the heap.
- Support both LAN interfaces as LAN(0) and LAN(1), with LAN(1)
being the 1GB interface.
The dual LAN port interface can eventually be adapted as well for the
RT1062 MCU.
This work was done in collaboration with @alphaFred.
This issue affected i.MX RT 1052, 1062 and 1064. It seems to be addressed
by Errata ERR006223, which also mentions i.MX RT101x and 102x, but these
devices worked well even without the change. As a side effect, the current
consumption at an idle REPL drops significantly with this fix.
Fixes issue #7235.
The new teensy loader keeps the file system under certain conditions:
- The file size is properly set in the file header.
- The header version is 4.3
These changes are implemented here, requiring a backport of
fsl_flexspi_nor_boot.c. There is still a problem with the command line
version of the teensy loader, which fails on the first attempt. At the
second attempt it works. The GUI version of the teensy loader is fine.
Changes in this commit:
- Manifest include's now use the directory path where possible (no longer
necessary to include the manifest.py file explicitly).
- Add manifest.py for all drivers and components that are referenced by
port/board manifests.
- Replace all uses of freeze() with package()/module(), except for port and
board modules.
- Use opt=3 everywhere, for consistency and to reduce code size.
- Use require() instead of include() for all micropython-lib references.
- Remove support for optional board-level manifest.py in mimxrt port, to
make it behave the same as other ports (the board must set
FROZEN_MANIFEST to a custom manifest.py, which can optionally include the
default, port-level manifest).
- Also reinstates modules that were accidentally removed from the esp8266
512k build in fbe9417b90.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
Replaces preprocessor macro for SDRAM option from #ifdef to #if in order to
allow always setting the define `MICROPY_HW_SDRAM_AVAIL` just with the
appropriate value 0/1. This eliminates one `if` in the Makefile.
The nxp_driver v2.10 allows for/requires some changes to the code:
- Remove some part of pwm_backlog.*, which is provided by the lib now.
- Change eth.c: the newer versions have additional parameters of the
library versions.
- Change sdcard.c: use TransferBlocking instead of TransferNonblocking.
- Add some support for the MIMXRT1176 device.
- Set the clocks for UART, I2C, Timer.
- Integrate the I2S module and fix a rebase error.
- Use blocking transfer only for SPI. It's faster and interferes less with
other modules.
- Use the clock_config.c files of library v2.8.5. The mimxrt files keeps
the clock_config.c files from Verson 2.8.5. With clock_config.c from
v2.10, the boards do not work. Refactoring of the clock set-up is on the
to-do list.
- Enable expiry timers for UART, I2C and SPI, avoiding a stall in library
code.
- The clock_config.* files are moved from the board-specific directories to
the boards directory and given a MCU related name.
This commit adds support for machine.I2S on the mimxrt port. The I2S API
is consistent with the existing stm32, esp32, and rp2 implementations.
I2S features:
- controller transmit and controller receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequencies from 8kHz to 48kHz
- 3 modes of operation:
- blocking
- non-blocking with callback
- uasyncio
- configurable internal buffer
- optional MCK
Tested with the following development boards:
- MIMXRT1010_EVK, MIMXRT1015_EVK, MIMXRT1020_EVK, MIMXRT1050_EVK
- Teensy 4.0, Teensy 4.1
- Olimex RT1010
- Seeed ARCH MIX
Tested with the following I2S hardware peripherals:
- UDA1334
- GY-SPH0645LM4H
- WM8960 codec on board the MIMXRT boards and separate breakout board
- INMP441
- PCM5102
- SGTL5000 on the Teensy audio shield
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
OCOTP_Init() has been removed from mphalport.c. The library files are
missing for the MIMXRT1015, and for just reading the OCOTP the Init is not
required.
The board.json file is intentionally excluded, until the board will be
sold. But including it into the mimxrt series make it easier to keep
the build up-to-date.
Using the keyword argument cs=nnn in the constructor. The cs1
pin has to be defined in mpconfigboard.h.
Note: Only a few boards have the CS1 pin exposed to the connectors.
iabdalkader