- Completes a longstanding TODO in the code, to not ignore
the optional family, type, proto and flags arguments to
socket.getaddrinfo().
- Note that passing family=socket.AF_INET6 will now cause queries
to fail (OSError -202). Previously this argument was ignored so
IPV4 results were returned instead.
- Optional 'type' argument is now always copied into the result. If not
set, results have type SOCK_STREAM.
- Fixes inconsistency where previously querying mDNS local suffix (.local)
hostnames returned results with socket type 0 (invalid), but all other
queries returned results with socket type SOCK_STREAM (regardless of
'type' argument).
- Optional proto argument is now returned in the result tuple, if supplied.
- Optional flags argument is now passed through to lwIP. lwIP has handling
for AI_NUMERICHOST, AI_V4MAPPED, AI_PASSIVE (untested, constants for
these are not currently exposed in the esp32 socket module).
- Also fixes a possible memory leak in an obscure code path
(lwip_getaddrinfo apparently sometimes returns a result structure with
address "0.0.0.0" instead of failing, and this structure would have been
leaked.)
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
CPython says thread identifier is a "nonzero integer", so rp2 should use a
1-indexed core number rather than 0-indexed. This fixes the
thread/thread_ident1 test failure on rp2 port.
Unfortunately this may be a breaking change for rp2 code which makes a
hard-coded comparison of thread identifier to 0 or 1.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
If there are any free chunks found then it's better to sweep the filesystem
and use the available chunks, rather than error out with ENOSPC when there
is in fact a bit of space remaining.
Signed-off-by: Damien George <damien@micropython.org>
Increases firmware size by +140 bytes and uses +4 extra bytes of RAM, but
allows the test suite to run without crashing.
Signed-off-by: Damien George <damien@micropython.org>
Flash sectors should start counting at 0 for each bank. This commit makes
sure that is the case on all H5 and H7 MCUs, by using `get_page()` instead
of `flash_get_sector_info()`.
Signed-off-by: Damien George <damien@micropython.org>
This commit removes the need for a separate `flash_cache_sector_id`
variable, instead using `flash_cache_sector_start` to indicate which sector
is curretly cached (and -1 indicates no sector).
Signed-off-by: Damien George <damien@micropython.org>
An erase sector sits in a given flash bank and some MCUs have two flash
banks. If trying to erase a range of sectors and that range crosses from
one flash bank into the next, the original implementation of
`flash_erase()` would not handle this case and would do the wrong thing.
This commit changes `flash_erase()` to only erase a single sector, which
sidesteps the need to handle flash-bank-crossing. Most callers of this
function only need to erase a single sector anyway.
Signed-off-by: Damien George <damien@micropython.org>
Newer STM32 parts have homogeneous flash layout, and in this case the MCU
configuration and page/sector calculation can be simplified. The affected
functions are `flash_is_valid_addr()` and `flash_get_sector_info()`, which
are now simpler for homogeneous flash.
Signed-off-by: Damien George <damien@micropython.org>
This commit replaces the linker symbol `_mboot_writable_flash_start` with
`_mboot_protected_flash_start` and `_mboot_protected_flash_end_exclusive`,
to provide better configuration of the protected flash area.
Signed-off-by: Damien George <damien@micropython.org>
Following ad806df857 where the
MICROPY_PY_PENDSV_ENTER/REENTER/EXIT macro definitions were moved to
mphalport.h.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this commit there is a potential deadlock in
mp_thread_begin_atomic_section(), when obtaining the atomic_mutex, in the
following situation:
- main thread calls mp_thread_begin_atomic_section() (for whatever reason,
doesn't matter)
- the second core is running so the main thread grabs the mutex via the
call mp_thread_mutex_lock(&atomic_mutex, 1), and this succeeds
- before the main thread has a chance to run save_and_disable_interrupts()
a USB IRQ comes in and the main thread jumps off to process this IRQ
- that USB processing triggers a call to the dcd_event_handler() wrapper
from commit bcbdee2357
- that then calls mp_sched_schedule_node()
- that then attempts to obtain the atomic section, calling
mp_thread_begin_atomic_section()
- that call then blocks trying to obtain atomic_mutex
- core0 is now deadlocked on itself, because the main thread has the mutex
but the IRQ handler (which preempted the main thread) is blocked waiting
for the mutex, which will never be free
The solution in this commit is to use mutex enter/exit functions that also
atomically disable/restore interrupts.
Fixes issues #12980 and #13288.
Signed-off-by: Damien George <damien@micropython.org>
Using the multicore lockout feature in the general atomic section makes it
much more difficult to get correct.
Signed-off-by: Damien George <damien@micropython.org>
This commit enables additional features for SAMD21 with external flash:
- Viper and native code support. On a relatively slow devices, viper and
native code can be helpful.
- Freeze the asyncio scripts and add the select module.
- Enable Framebuffer support.
- Enable UART flow control.
- Enable a few more features from the extra features set.
Drop onewire and asyncio support from SAMD21 firmware without external
flash, leaving a little bit more room for future extensions. Asyncio was
anyhow incomplete.
Signed-off-by: robert-hh <robert@hammelrath.com>
RTC is enabled on all boards. Therefore the conditional compile is not
needed. Removing it simplifies the source code a little bit.
Signed-off-by: robert-hh <robert@hammelrath.com>
Instead, configure the default once at compile-time. This means the GAP
name will no longer be set to default after re-initializing Bluetooth.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
This commit implements fairly complete support for the DMA controller in
the rp2 series of microcontrollers. It provides a class for accessing the
DMA channels through a high-level, Pythonic interface, and functions for
setting and manipulating the DMA channel configurations.
Creating an instance of the rp2.DMA class claims one of the processor's DMA
channels. A sensible, per-channel default value for the ctrl register can
be fetched from the DMA.pack_ctrl() function, and the components of this
register can be set via keyword arguments to pack_ctrl().
The read, write, count and ctrl attributes of the DMA class provide
read/write access to the respective registers of the DMA controller. The
config() method allows any or all of these values to be set simultaneously
and adds a trigger keyword argument to allow the setup to immediately be
triggered. The read and write attributes (or keywords in config()) accept
either actual addresses or any object that supports the buffer interface.
The active() method provides read/write control of the channel's activity,
allowing the user to start and stop the channel and test if it is running.
Standard MicroPython interrupt handlers are supported through the irq()
method and the channel can be released either by deleting it and allowing
it to be garbage-collected or with the explicit close() method.
Direct, unfettered access to the DMA controllers registers is provided
through a proxy memoryview() object returned by the DMA.registers attribute
that maps directly onto the memory-mapped registers. This is necessary for
more fine-grained control and is helpful for allowing chaining of DMA
channels.
As a simple example, using DMA to do a fast memory copy just needs:
src = bytearray(32*1024)
dest = bytearray(32*1024)
dma = rp2.DMA()
dma.config(read=src, write=dest, count=len(src) // 4,
ctrl=dma.pack_ctrl(), trigger=True)
# Wait for completion
while dma.active():
pass
This API aims to strike a balance between simplicity and comprehensiveness.
Signed-off-by: Nicko van Someren <nicko@nicko.org>
Signed-off-by: Damien George <damien@micropython.org>
This allows to follow good practice and have libraries live in the lib
folder which means they will be found by the runtime without adding this
path manually at runtime.
Signed-off-by: Sebastian Romero <s.romero@arduino.cc>
MicroPython code may rely on the return value of sys.stdout.buffer.write()
to reflect the number of bytes actually written. While in most scenarios a
write() operation is successful, there are cases where it fails, leading to
data loss. This problem arises because, currently, write() merely returns
the number of bytes it was supposed to write, without indication of
failure.
One scenario where write() might fail, is where USB is used and the
receiving end doesn't read quickly enough to empty the receive buffer. In
that case, write() on the MicroPython side can timeout, resulting in the
loss of data without any indication, a behavior observed notably in
communication between a Pi Pico as a client and a Linux host using the ACM
driver.
A complex issue arises with mp_hal_stdout_tx_strn() when it involves
multiple outputs, such as USB, dupterm and hardware UART. The challenge is
in handling cases where writing to one output is successful, but another
fails, either fully or partially. This patch implements the following
solution:
mp_hal_stdout_tx_strn() attempts to write len bytes to all of the possible
destinations for that data, and returns the minimum successful write
length.
The implementation of this is complicated by several factors:
- multiple outputs may be enabled or disabled at compiled time
- multiple outputs may be enabled or disabled at runtime
- mp_os_dupterm_tx_strn() is one such output, optionally containing
multiple additional outputs
- each of these outputs may or may not be able to report success
- each of these outputs may or may not be able to report partial writes
As a result, there's no single strategy that fits all ports, necessitating
unique logic for each instance of mp_hal_stdout_tx_strn().
Note that addressing sys.stdout.write() is more complex due to its data
modification process ("cooked" output), and it remains unchanged in this
patch. Developers who are concerned about accurate return values from
write operations should use sys.stdout.buffer.write().
This patch might disrupt some existing code, but it's also expected to
resolve issues, considering that the peculiar return value behavior of
sys.stdout.buffer.write() is not well-documented and likely not widely
known. Therefore, it's improbable that much existing code relies on the
previous behavior.
Signed-off-by: Maarten van der Schrieck <maarten@thingsconnected.nl>
This adds support to stm32's mboot for the Microsoft WCID USB 0xee string
and Compatible ID Feature Descriptor. This allows the USB device to
automatically set the default USB driver, so that when the device is
plugged in Windows will assign the winusb driver to it. This means that
USB DFU mode can be used without installing any drivers.
For example this page will work (allow the board to be updated over DFU)
with zero install: https://devanlai.github.io/webdfu/dfu-util/
Tested on Windows 10, Windows can read the 0xee string correctly, and
requests the second special descriptor, which then configures the USB
device to use the winusb driver.
Signed-off-by: Damien George <damien@micropython.org>
This gets back the old heap-size behaviour on ESP32, before auto-split-heap
was introduced: after the heap is grown one time the size is 111936 bytes,
with about 40k left for the IDF. That's enough to start WiFi and do a
HTTPS request.
Signed-off-by: Damien George <damien@micropython.org>
Add new board Silicognition RP2040-Shim, RP2040 with 4 MB of flash
and W5500 drivers included and configured by default for use with
the Silicognition PoE-FeatherWing.
Co-authored-by: Matt Trentini <matt.trentini@gmail.com>
Signed-off-by: Patrick Van Oosterwijck <patrick@silicognition.com>
Some boards have multiple options for these pins, and they don't want to
allow users to initialize a port without explicitly specifying pin numbers.
Signed-off-by: Paul Grayson <paul@pololu.com>
esp8266 doesn't need ets task because the notify is now scheduled (see
commits 7d57037906 and
c60caf1995 for relevant history).
Signed-off-by: Damien George <damien@micropython.org>
Also, IDF v5.1.2 is now supported, just not used by default.
IDF v5.0.2 still builds but we cannot guarantee continued support for this
version moving forward.
Signed-off-by: IhorNehrutsa <IhorNehrutsa@gmail.com>
Disable unused EC curves and default certificate bundle which is not
implemented in MicroPython. This reduces the firmware size significantly.
This follows commit 68f166dae9.
Signed-off-by: Carlos Gil Gonzalez <carlosgilglez@gmail.com>
Necessary to get coverage of the new event functions.
Deletes the case that called usleep(delay) for mp_hal_delay_ms(), it seems
like this wouldn't have ever happened anyhow (MICROPY_EVENT_POOL_HOOK is
always defined for the unix port).
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This is necessary to avoid watchdog timeout in long i2c.scan(), as
previously machine_i2c.c would call MICROPY_EVENT_POLL_HOOK if
MICROPY_EVENT_POLL_HOOK_FAST was not available.
Compared to previous implementation, this implementation removes the
ets_event_poll() function and calls the SDK function ets_loop_iter() from
MICROPY_INTERNAL_EVENT_HOOK instead. This allows using the port-agnostic
functions in more places.
There is a small behaviour change, which is that the event loop gets
iterated in a few more places (i.e. anywhere that mp_event_handle_nowait()
is called). However, this looks like maybe only modselect.c - and is
probably good to process Wi-Fi events in that polling loop.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This should be the equivalent of the previous event poll hook macro.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Previously this was not set, so potential for race conditions in interrupt
handlers this didn't issue SEV. (Which is currently all of them, as far as
I can see.)
Eventually we might be able to augment the interrupt handlers that wake the
main thread to call SEV, and leave the others as-is to suspend the CPU
slightly faster, but this will solve the issue for now.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit changes all uses in the rp2 port, and drivers that are
optionally supported by that port.
The old MICROPY_EVENT_POLL_HOOK and MICROPY_EVENT_POLL_HOOK_FAST macros are
no longer used for rp2 builds and are removed (C user code will need to be
changed to suit).
Also take the opportunity to change some timeouts that used 64-bit
arithmetic to 32-bit, to hopefully claw back a little code size.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This header has no include guards and is apparently only supposed to be
included from py/mphal.h.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit fixes all known floating-point bugs with the pico-sdk. There
are two things going on here:
- Use a custom pico float component so that the pico-sdk doesn't include
its math functions, and then provide our own from lib/libm.
- Provide a wrapper for __aeabi_fadd to fix the infinity addition bug.
Prior to this commit, the following tests failed on the rp2 port: cmath_fun
float_parse math_domain math_domain_special math_fun_special. With this
commit, all these tests pass.
Thanks to @projectgus for how to approach this fix.
Signed-off-by: Damien George <damien@micropython.org>
The installation instructions for ESP32 TinyPICO board contained a typo
that used a non-standard baud rate 912600 instead of 921600. This made the
upload command fail on some Windows computers.
Signed-off-by: Scott Zhao <zhaomh1998@outlook.com>
The user memory area - accessible by machine.RTC.memory() -- will now
survive most reboot causes. A power-on reset (also caused by the EN pin on
some boards) will clean the memory. When this happens, the magic number
not found in the user memory will cause initialization.
After other resets (triggered by watchdogs, machine.reset(), ...), the user
is responsible to check and validate the contents of the user area.
This new behaviour can be changed by enabling
MICROPY_HW_RTC_MEM_INIT_ALWAYS: in that case the RTC memory is always
cleared on boot.
Signed-off-by: Thomas Wenrich <twenrich@gmail.com>
The amount of free IRAM in ESP32 SPIRAM builds is very small and went over
the limit due to commit 30b0ee34d3. This
commit enables further optimisations to reduce IRAM usage.
Signed-off-by: Damien George <damien@micropython.org>
Configures the I2S PLL to produce a frequency that the I2S clock generator
can use to create an optimal SCK frequency. The I2S PLL configuration
table is automatically generated at build time.
Fixes issue #10280.
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
This board has MICROPY_VFS enabled, which should take precedence over
MICROPY_MBFS (and did prior to 22d9116c8c).
Signed-off-by: Damien George <damien@micropython.org>
All ports using this common configuration already enable time/date
validation, so this commit is a no-op change.
Signed-off-by: Damien George <damien@micropython.org>
Also move MICROPY_PY_PENDSV_ENTER/REENTER/EXIT to mphalport.h, for ports
where these are not already there.
This helps separate the hardware implementation of these macros from the
MicroPython configuration (eg for renesas-ra and stm32, the IRQ static
inline helper functions can now be moved to irq.h).
Signed-off-by: Damien George <damien@micropython.org>
Changes:
- os.uname() is removed to save space; sys.version and sys.implementation
can be used instead.
- os.sync() now uses the common extmod version and syncs by calling the FAT
FS sync function, which eventually calls sflash_disk_flush().
Signed-off-by: Damien George <damien@micropython.org>
The os.dupterm() function has changed on this port, it now matches the
semantics used by all other ports (except it's restricted to accept only
machine.UART objects).
Signed-off-by: Damien George <damien@micropython.org>
Now that the MICROPY_BEGIN_ATOMIC_SECTION/MICROPY_END_ATOMIC_SECTION macros
act the same as disable_irq/enable_irq, it's possible to use the common
extmod implementation of these machine functions.
Signed-off-by: Damien George <damien@micropython.org>
This commit changes the cc3200 port to use the common machine
implementation of machine.disable_irq() and machine.enable_irq(). This
eliminates its dependency on the stm32 port's code. The behaviour of
cc3200 for these functions is changed:
- disable_irq() now returns an (opaque) integer rather than a bool
- enable_irq(state) must be passed and argument, which is the return value
of disable_irq() rather than a bool
Signed-off-by: Damien George <damien@micropython.org>
The ports esp32, mimxrt, rp2 and samd all shared exactly the same
implementation of machine.disable_irq() and machine.enable_irq(),
implemented in terms of MICROPY_{BEGIN,END}_ATOMIC_SECTION. This commit
factors these implementations into extmod/modmachine.c.
The cc3200, esp8266, nrf, renesas-ra and stm32 ports do not yet use this
common implementation.
Signed-off-by: Damien George <damien@micropython.org>
Minor changes for consistency are:
- nrf gains: unique_id(), freq() [they do nothing]
- samd: deepsleep() now resets after calling lightsleep()
- esp32: lightsleep()/deepsleep() no longer take kw arg "sleep", instead
it's positional to match others. also, passing 0 here will now do a 0ms
sleep instead of acting like nothing was passed.
reset_cause() no longer takes any args (before it would just ignore them)
- mimxrt: freq() with an argument and lightsleep() both raise
NotImplementedError
Signed-off-by: Damien George <damien@micropython.org>
And use it in all ports. The ports are unchanged, except esp8266 which now
just returns None from this function instead of the time elapsed (to match
other ports), and qemu-arm which gains this function.
Signed-off-by: Damien George <damien@micropython.org>
This is a code factoring to have the dict for the machine module in one
location, and all the ports use that same dict. The machine.soft_reset()
function implementation is also factored because it's the same for all
ports that did already implement it. Eventually more functions/bindings
can be factored.
All ports remain functionally the same, except:
- cc3200 port: gains soft_reset, mem8, mem16, mem32, Signal; loses POWER_ON
(which was a legacy constant, replaced long ago by PWRON_RESET)
- nrf port: gains Signal
- qemu-arm port: gains soft_reset
- unix port: gains soft_reset
- zephyr port: gains soft_reset, mem8, mem16, mem32
Signed-off-by: Damien George <damien@micropython.org>
Prior to this change, if a board did not define any hardware I2C pins, via
MICROPY_HW_I2Cx_SCL, then machine.I2C would alias to machine.SoftI2C.
That doesn't really make sense, and SoftI2C should always be used if there
is no hardware implementation. So this commit makes it so that machine.I2C
is only available if at least one set of I2C hardware pins are defined via
the MICROPY_HW_I2Cx_SCL/SDA macros.
For all boards that define at least one set of I2C hardware pins (which is
most of them) this commit is a no-op. The only boards that change are:
LEGO_HUB_NO6, LEGO_HUB_NO7, STM32H7B3I_DK.
Signed-off-by: Damien George <damien@micropython.org>
MICROPY_PY_MACHINE_SPI is defined in mpconfigport.h to be equal to
MICROPY_PY_MACHINE_HW_SPI, so they are equivalent options. The former one
is preferred because it's used by all other ports.
The default in mpconfigport.h is to enable this option, and all boards that
enable SPI have this removed from their mpconfigboard.h file so they pick
up the default.
Signed-off-by: Damien George <damien@micropython.org>
best_effort_wfe_or_timeout() already calls time_reached() and returns the
result of it, so no need to call it again.
Signed-off-by: Damien George <damien@micropython.org>
If a port defines MICROPY_SOFT_TIMER_TICKS_MS then soft_timer assumes a
SysTick back end, and provides a soft_timer_next variable that sets when
the next call to soft_timer_handler() should occur.
Otherwise, a port should provide soft_timer_get_ms() and
soft_timer_schedule_at_ms() with appropriate semantics (see comments).
Existing users of soft_timer should continue to work as they did.
Signed-off-by: Damien George <damien@micropython.org>
Commit 7ea06a3e26 moved the
`rmt_write_items()` call to fix RMT looping for ESP32-S3, but broke it for
the other ESP32s. This commit conditionally compiles the location of that
call.
Signed-off-by: Mark Blakeney <mark.blakeney@bullet-systems.net>
Prior to this change, after calling connect() the status() method for the
STA interface would either return STAT_GOT_IP or STAT_CONNECTION. The
latter would be returned because wifi_sta_connect_requested==true and
conf_wifi_sta_reconnects==0 by default. As such there was no way to know
anything about errors when attempting to connect, such as a bad password.
Now, status() can return STAT_NO_AP_FOUND and STAT_WRONG_PASSWORD when
those conditions are met.
Fixes issue #12930.
Signed-off-by: IhorNehrutsa <Ihor.Nehrutsa@gmail.com>
In ESP-IDF, enabling SPIRAM in menuconfig sets some Kconfig options:
- "Wi-Fi Cache TX Buffers" enabled. By default this tries to allocate 32 of
these when Wi-Fi is initialised, which requires 54,400 bytes of free heap.
- Switches "Type of WiFi TX buffers" from Dynamic to Static. This
pre-allocates all of the Wi-Fi transmit buffers.
Not a problem if PSRAM is initialised, but it's quite a lot of RAM if PSRAM
failed to initialise! As we use the same config for PSRAM & no-PSRAM builds
now, this either causes Wi-Fi to fail to initialise (seen on S2) or will
eat quite a lot of RAM.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
In commit 7c929d44 the console UART was changed to use the UART HAL.
Starting the UART HAL will change the UART clock from whatever it was
already configured at to UART_SCLK_DEFAULT. There is no "initialize at
existing settings" option.
This clock doesn't work with DFS.
The ESP-IDF code already takes this into account, and when DFS is enabled
it will configure the console UART to use the correct platform-specific
clock that will work with DFS.
The UART HAL init undoes this and sets it back to default.
This change will query the clock before the HAL init, then use the HAL
function to restore it back. Thus keeping the clock at the "correct"
value, which depends on platform, DFS status, and so on.
The clock frequency will be found using the UART driver function ESP-IDF
code uses for this. The existing code hard-coded a path that worked if the
clock was the APB clock and would fail otherwise.
The UART_NUM_0 define is removed because driver/uart.h already provides
this same macro.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
The behaviour described in the docs was not correct for either port.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
At some point the config changed such that no messages above Error level
were compiled into the final binary.
Fixes issue #12815.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
If the hard socket limit (default 16) is reached then it's possible that
socket allocation fails but garbage collection would allow it to succeed.
Perform a GC pass and try again before giving up, similar to the logic
elsewhere in MicroPython that tries a GC pass before raising MemoryError.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
LWIP doesn't implement a timeout for blocking connect(), and such a timeout
is not required by POSIX. However, CPython will use the socket timeout for
blocking connect on most platforms. The "principle of least surprise"
suggests we should support it on ESP32 as well (not to mention it's
useful!).
This provides the additional improvement that external exceptions (like
KeyboardInterrupt) are now handled immediately if they happen during
connect(). Previously Ctrl-C would not terminate a blocking connect until
connect() returned, but now it will.
Fixes issue #8326.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit changes the Arduino board identifiers to correspond to their
official names. This helps to identify boards at runtime. At the moment
the Arduino Portenta H7 is reported as PORTENTA which is unfortunate as now
there is another Portenta board (Portenta C33) supported in MicroPython.
Also made the other identifiers for flash and network name consistent,
removed the incorrectly used MICROPY_PY_SYS_PLATFORM identifiers, and added
missing MICROPY_PY_NETWORK_HOSTNAME_DEFAULT identifiers.
Boards affected:
- stm32: ARDUINO_PORTENTA_H7, ARDUINO_GIGA, ARDUINO_NICLA_VISION
- renesas-ra: ARDUINO_PORTENTA_C33
- esp32: ARDUINO_NANO_ESP32
- rp2: ARDUINO_NANO_RP2040_CONNECT
Signed-off-by: Sebastian Romero <s.romero@arduino.cc>
Configuration:
- Clock is HSE, CPU runs at 250MHz.
- REPL on USB and UART connected to the ST-Link interface.
- Storage is configured for internal flash memory.
- Three LEDs and one user button.
- Ethernet is enabled.
Signed-off-by: Rene Straub <rene@see5.ch>
Replaces the previous all-zeroes "TODO" serial number.
Requires refactoring the low-level unique_id routine out from modmachine.c.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Change the rp2 and renesas-ra ports to use the helper function.
Saves copy-pasta, at the small cost of one more function call in the
firmware (if not using LTO).
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Functionality and code size don't really change, but removes port-specific
code in favour of shared code.
(The MSC implemented in shared/tinyusb depends on some functions in the
pico-sdk, so this change doesn't make this available for samd.)
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
See the commit a00c9d56db for a detailed description of the problem, a
regression introduced in 26d503298.
Same approach here as the linked fix for rp2 (applied unconditionally here
as this port only supports USB-CDC for stdin/stdout).
Signed-off-by: Angus Gratton <angus@redyak.com.au>
The recent change in bcbdee2357 means that
TinyUSB can no longer be run from within a soft (or hard) IRQ handler, ie
when the scheduler is locked. That means that Python code that calls
`print(...)` from within a scheduled function may block indefinitely if the
USB CDC buffers are full.
This commit fixes that problem by explicitly running the TinyUSB stack when
waiting within stdio tx/rx functions.
Signed-off-by: Damien George <damien@micropython.org>
This adds the sync version of the LoRa driver (and the base WL55 driver).
Adds +13.6kiB (212.6 -> 226.2). Limit for this board is 232kiB.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
If you have a variable frequency and pulse width, and you want to optimize
pulse resolution, then you must do a calculation beforehand to ensure you
normalize the array to keep all list values within bound. That calculation
requires RMT.source_freq(), RMT.clock_div(), and this 32767 constant.
Signed-off-by: Mark Blakeney <mark.blakeney@bullet-systems.net>
To create an esp32.RMT() instance with an optimum (i.e. highest resolution)
clock_div is currently awkward because you need to know the source clock
frequency to calculate the best clock_div, but unfortunately that is only
currently available as an source_freq() method on the instance after you
have already created it. So RMT.source_freq() should really be a class
method, not an instance method. This change is backwards compatible for
existing code because you can still reference that function from an
instance, or now also, from the class.
Signed-off-by: Mark Blakeney <mark.blakeney@bullet-systems.net>
Previously the TinyUSB task was run in the ISR immediately after the
interrupt handler. This approach gives very similar performance (no change
in CDC throughput tests) but reduces the amount of time spent in the ISR,
and allows TinyUSB callbacks to run in thread mode.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This change:
- Has a small code size reduction.
- Should slightly improve overall performance. The old hook code
seemed to use between 0.1% and 1.6% of the total CPU time doing no-op
calls even when no USB work was required.
- USB performance is mostly the same, there is a small increase in
latency for some workloads that seems to because sometimes the hook
usbd_task() is called at the right time to line up with the next USB host
request. This only happened semi-randomly due to the timing of the hook.
Improving the wakeup latency by switching rp2 to tickless WFE allows the
usbd_task() to run in time for the next USB host request almost always,
improving performance and more than offsetting this impact.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Add a .ico file with common icon image size, created from
vector-logo-2.png, and embed it into the resulting executable.
Signed-off-by: stijn <stijn@ignitron.net>
This is a code factoring to have the Python bindings in one location, and
all the ports use those same bindings. At this stage only esp32 implements
this class, so the code for the bindings comes from that port.
The documentation is also updated to reflect the esp32's behaviour of
ADCBlock.connect().
Signed-off-by: Damien George <damien@micropython.org>
C99 says that strncmp has UB for either string being NULL, so the
current behavior is technically correct, but it's an easy fix to handle
this case correctly.
7.1.4: "unless explicitly stated otherwise in the detailed
description... if an argument to a function has ...null pointer.. the
behavior is undefined".
7.21.1: "Unless explicitly stated otherwise in the description of a
particular function in this subclause, pointer arguments on such a call
shall still have valid values, as described in 7.1.4".
Also make the same change for the minimal version in bare-arm/lib.c.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Remove port-specific test directories and excluded tests from
tinytest-codegen, and let it read said information from an external file.
This way tinytest-codegen is not limited to always generate tests for the
`qemu-arm` target.
This allows having port-specific test directory and excluded tests for more
than one QEMU bare-metal target.
The `qemu-arm` port Makefile was modified to work with the generator
changes and a tests profile file was added to said port.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
Changing the baudrate requires a complete re-configuration of the Sercom
device, which is put into a separate rather large function. This new
machine_uart_set_baudrate() function will be useful for future drivers such
as Bluetooth.
Signed-off-by: robert-hh <robert@hammelrath.com>
Fixes are:
- Only emit ADC table entries for pins that aren't cpu-hidden
(i.e. ignore `X,-Y` rows).
- Only use the P channels on H7.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The main motivation for doing this was to reduce the latency when the
system is woken by a USB interrupt. The best_effort_wfe_or_timeout()
function calls into the pico-sdk dynamic timer framework which sets up a
new dynamic timer instance each time, and then has to tear it down before
continuing after a WFE.
Testing Python interrupt latency, it seems to be improved by about 12us
(from average of 46us to 34us running a Pin IRQ). C-based "scheduled
nodes" should see even lower latency.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This patch ensures that integer channel numbers passed to the ADC
constructor (including temperature sensor) are interpreted as raw
channel numbers, and not cause any GPIO pins to be initialized.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
The FIFO reports not only the bytes read, but also 4 error bits. These were
not checked, leading to NUL value read in case of break and possible
garbage bytes being written on parity/framing error.
This patch addresses the issue that NUL bytes are incorrectly read on
break, and at least provides the boilerplate code and comments for error
handling, that may be implemented in the future.
Signed-off-by: Maarten van der Schrieck <maarten@thingsconnected.nl>
Update rtc, machine and powerctrl drivers to support STM32H5 sleep
modes. This makes RTC alarm wakeup working from lightsleep() and
deepsleep().
Changes:
- Determine start reason for machine.reset_cause() in modmachine.c.
- Add proper interrupt clear code in rtc.c.
- Add wakeup functionality in powerctrl_enter_stop_mode(). Remember
and restore voltage scaling level. Restart HSI48 if it was on before
entering sleep mode.
- Clear DBGMCU_CR in SystemClock_Config() as for other variants.
Otherwise debug flags prevent entering sleep mode.
Implementation Notes:
- rtc.c: EXTI_RTSTR1 bits are not present for H5. Code sequence from
G0/G4/L4/WB/WL would be invalid. RTSTR is only defined for external
(GPIO) interrupts. Maybe this is also true for other STM32 variants.
- powerctrl_enter_stop_mode() uses complicated, nested conditionals
to select STM32 variants. To make code slightly better readable,
comment have been added. A non-nested, #if/#elif sequence would
make the code more readable. I leave this to the original authors.
Signed-off-by: Rene Straub <rene@see5.ch>
This fixes the case where e.g.
struct foo_t {
mp_obj_t x;
uint16_t y;
char buf[];
};
will have `sizeof(struct foo_t)==8`, but `offsetof(struct foo_t, buf)==6`.
When computing the size to allocate for `m_new_obj_var` we need to use
offsetof to avoid over-allocating. This is important especially when it
might cause it to spill over into another GC block.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It's not worth the effort to update these ports to use boardgen.py, but
put a note just in case anyone uses this as a reference for a new port.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This removes previously unused functionality to generate pins_ad_const.h,
as well as the unused handling of pin AF in machine_pin.c.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Minor change to remove support for using numeric IDs for machine.Pin. This
was previously based on the index of the pin in the board csv, but this is
different (and incompatible) with other ports.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This replaces the previous make-pin-table.py with an implementation based
on boardgen.py.
- MICROPY_PY_MACHINE_PIN_BOARD_CPU macro is removed. This isn't optional
on other ports, so no need for it to be optional on SAMD.
- pin_af_table is removed, and lookups just search the cpu dict instead
(this saves N*wordsize bytes of firmware size to have this extra table).
- pins.csv is now BOARD,CPU to match other ports.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This fixes the H7 af.csv files to include the dual-pad information, by
listing the ADCs supported on the _C pad with a C_ADC prefix.
Minimal change to make-pins.py to ignore these entries. This will be
implemented later to emit constants (similar to ADC.CORE_TEMP) to access
these channels.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Requires additions to tools/boardgen.py for stm32 pin generation.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is now consistent with other ports.
Also renamed `pin_{board/cpu}_pins_locals_dict` to
`machine_pin_{board/cpu}_pins_locals_dict`.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Changes are:
- Pad all cells to make them easier to read.
- Ensure all files have exactly 19 columns (Port,Pin,AF0-15,ADC)
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Fixes are:
- Comment out lines in pins.csv that do not have valid CPU pins.
It's useful to keep these in the file as "documentation" but in order to
make make-pins.py stricter they need to be commented out.
- Fix some typos (missing P prefix) in pins.csv.
This resulted in some missing board pins.
- Fix some typos in af.csv files.
Some typos of "ADC" and some other that were previously ignored.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
For now, this implements the functionality required for esp32 and rp2,
including support for numeric pins, rp2 alternate functions, and rp2
extended pins.
This also updates the rp2 port to use the same structure for pins.h and
pins.csv as for esp32, and moves the pin definitions directly into the
table (rather than having a table of pointers), which is a small code size
improvement.
Support for "hidden" pins in pins.csv is added (matching the stm32
implementation).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
All ports now use `--board-csv`, `--prefix`, `--output-souce`,
`--output-header` and no longer write to stdout. This matches the esp32
implementation.
Ports that have an AF input use `--af-csv` (to match `--board-csv`).
Any additional output files are now prefixed with `output-` (e.g.
`--output-af-const`).
Default arguments are removed (all makefiles should always specify all
arguments, using default values is likely an error).
Replaced the `af-defs-cmp-strings` and `hdr-obj-decls` args for stm32 with
just `mboot-mode`. Previously they were set on the regular build, now the
logic is reversed so mboot sets it.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It's not supported on all ports, adds complexity to the build to generate
pins_af.py, and can mostly be replicated just by printing the pin objects.
Remove support for generating pins_af.py from all ports (nrf, stm32,
renesas-ra, mimxrt, rp2).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The output pins.c can be processed for qstrs like any other C file.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The output pins.c can be processed for qstrs like any other C file.
Also remove af_const from Makefile (unimplemented in make-pins.py) and fix
target dependency on ad_const.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The output pins.c can be processed for qstrs like any other C file.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Qstrs are picked up from the generated pin source files in the usual qstr
processing stage.
Similarly for the stm constant qstrs.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Also remove af-const header, as this is left over from the STM32 version
and unused.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This prevents each port Makefile from having to add an explicit rule for
`build-BOARD/pins_BOARD.c`.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This updates a small number of files that change with ruff-format's (vs
black's) rules.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This improves (decreases) the latency on stdin, on SoCs with built-in USB
and using TinyUSB, like S2 and S3.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
ESP32-C3 is not Xtensa-based, so build settings are now tailored a bit
better following that fact. ESP-IDF 5.x already adds architecture-specific
modules by itself so there is no need to specify either the `xtensa` or the
`riscv` module in the build settings.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
Commit c4e63ace66 enabled the SPI Ethernet
driver and that cost about 13k of firwmare size, pushing the firmware over
the limit of the D2WD and OTA board variants available size.
To fix, disable SPI Ethernet on the D2WD variant, and build the OTA variant
with size optimisation rather than performance optimisation.
Signed-off-by: Damien George <damien@micropython.org>
This port is largely unmaintained, has limited features (the only hardware
support is for GPIO and timer, and no machine module), only supports a
small number of Teensy boards, and can be confused with the mimxrt support
for Teensy 4.x.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
nic.isconnected() returns now "True", if a) the physical link is up and b)
an IP address is assigned. The latter happens often by DHCP, in which case
an active connection can be assumed. If the IP address is set manually,
nic.isconnected() would report "True" as well, if at least the physical
link is up. This matches WLAN behaviour which returns "True" when the WLAN
has an IP address.
Before, the behaviour of nic.isconneceted() was erratic, returning "True"
sometimes even without a Ethernet cable attached.
Fixes issue #12741.
Signed-off-by: robert-hh <robert@hammelrath.com>
SPI support was not enabled, and was not adapted for esp-idf v5.x. This
change enables SPI ethernet for all boards and adapts the code for esp-idf
v5.x. The change follows the sample implementation of @hemakumarm72, but
adds the changes for the other adapters as well. Further, it simplifies
the code by removing actions from netwwork_lan.c which are done in the
esp-idf drivers later, like setting the default values for .command_bits
and .address_bits, and registering the SPI interface.
Tested with a Wiznet W5500 breakout.
Signed-off-by: robert-hh <robert@hammelrath.com>
Reduces the CPU usage by the PPP thread by sleeping for one tick if
there was nothing to read; preventing the loop using 100% CPU when the
read operation has a zero timeout and immediately returns.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
Instead use the generic default defined in modbluetooth_nimble.c.
This then also allows custom boards to easily override the default
Bluetooth GAP name.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
If data is pushed over serial/JTAG too fast we may fill up stdin_ringbuf
and not be able to read all the data out of the serial/JTAG buffer. Thus
we need to explicitly poll and read the serial/JTAG RX buffer to prevent
blocking (since if the serial/JTAG buffer is already filled, we will not
get another interrupt to transfer it to the stdin ringbuffer).
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
PPP code assumes that IPv6 support is enabled. Whilst this is the default,
certain applications may want to disable IPv6 support if not needed (or to
reduce code size).
This makes the code build with CONFIG_LWIP_IPV6 disabled, reducing code by
about 30k in that case.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
This provides a way to enable features and changes slated for MicroPython
2.x, by running `make MICROPY_PREVIEW_VERSION_2=1`. Also supported for
the cmake ports (except Zephyr).
This is an alternative to having a 2.x development branch (or equivalently,
keeping a 1.x release branch). Any feature or change that needs to be
"hidden" until 2.x can use this flag (either in the Makefile or the
preprocessor).
A good example is changing function arguments or other public API features,
in particular to aid in improving consistency between ports.
When `MICROPY_PREVIEW_VERSION_2` is enabled, the REPL banner is amended to
say "MicroPython (with v2.0 preview) vX.Y.Z", and sys.implementation gets a
new field `_v2` set to `True`.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The contents of machine_mem.h, machine_i2c.h and machine_spi.h have been
moved into extmod/modmachine.h.
Signed-off-by: Damien George <damien@micropython.org>
The contents of machine_bitstream.h, machine_pinbase.h, machine_pulse.h and
machine_signal.h have been moved into extmod/modmachine.h.
Signed-off-by: Damien George <damien@micropython.org>
The machine_i2c_type, machine_spi_type and machine_timer_type symbols are
already declared in extmod/modmachine.h and should not be declared anywhere
else.
Also move declarations of machine_pin_type and machine_rtc_type to the
common header in extmod.
Signed-off-by: Damien George <damien@micropython.org>
This is a code factoring to have the Python bindings in one location, and
all the ports use those same bindings. For all ports except the two listed
below there is no functional change.
The nrf port has UART.sendbreak() removed, but this method previously did
nothing.
The zephyr port has the following methods added:
- UART.init(): supports setting timeout and timeout_char.
- UART.deinit(): does nothing, just returns None.
- UART.flush(): raises OSError(EINVAL) because it's not implemented.
- UART.any() and UART.txdone(): raise NotImplementedError.
Signed-off-by: Damien George <damien@micropython.org>
No functional change, just code factoring to have the Python bindings in
one location, and all the ports use those same bindings.
Signed-off-by: Damien George <damien@micropython.org>
This commit makes it so that MICROPY_PY_MACHINE_PWM is enabled if at least
one of MICROPY_PY_MACHINE_HW_PWM and/or MICROPY_PY_MACHINE_SOFT_PWM are
enabled. This simplifies the configuration for boards, and fixes DVK_BL652
which enabled PWM without selecting software or hardware implementations.
With this change, DVK_BL652 and EVK_NINA_B1 now enable (hardware) PWM.
Signed-off-by: Damien George <damien@micropython.org>
iabdalkader