System config block contains hardware unrelated to USB. So calling
`__SYSCFG_CLK_DISABLE()` during `HAL_PCD_MspDeInit()` has an adverse effect
on other system functionality.
Removing call to `__SYSCFG_CLK_DISABLE()` to rectify this issue.
This call was there since the beginning of the USB CDC code, added in
b30c02afa0.
According to ST Errata ES0206 Rev 18, Section 2.2.1, on STM32F427x,
STM32F437x, STM32F429x and STM32F439x.
If the system tick interrupt is enabled during stop mode while certain
bits are set in the DBGMCU_CR, then the system will immediately wake
from stop mode.
Suggested workaround is to disable system tick timer interrupt when
entering stop mode.
According to ST Errate ES0394 Rev 11, Section 2.2.17, on STM32WB55Cx and
STM32WB35Cx.
If the system tick interrupt is enabled during stop 0, stop 1 or stop 2
while certain bits are set in DBGMCU_CR, then system will immediately
wake from stop mode but the system remains in low power state. The CPU
therefore fetches incorrect data from inactive Flash, which can cause a
hard fault.
Suggested workaround is to disable system tick timer interrupt when
entering stop mode.
This was added by mistake in 8f68e26f79 when
adding support for G4 MCUs, which does not using this get_bank() function.
FLASH_OPTR_DBANK is only defined on G4 and L4 MCUs, so on H7 this
FLASH_BANK_2 code was being wrongly excluded.
Signed-off-by: Damien George <damien@micropython.org>
Also remove redundant modusocket.c and modnetwork.c sources, they are
already added by extmod/extmod.cmake.
Signed-off-by: Damien George <damien@micropython.org>
The callback passed to add_alarm_in_ms must return microseconds, even
though the initial delay is in milliseconds. Fix this use, and to avoid
further confusion use the add_alarm_in_us function instead.
Signed-off-by: Damien George <damien@micropython.org>
The nxp_driver v2.10 allows for/requires some changes to the code:
- Remove some part of pwm_backlog.*, which is provided by the lib now.
- Change eth.c: the newer versions have additional parameters of the
library versions.
- Change sdcard.c: use TransferBlocking instead of TransferNonblocking.
- Add some support for the MIMXRT1176 device.
- Set the clocks for UART, I2C, Timer.
- Integrate the I2S module and fix a rebase error.
- Use blocking transfer only for SPI. It's faster and interferes less with
other modules.
- Use the clock_config.c files of library v2.8.5. The mimxrt files keeps
the clock_config.c files from Verson 2.8.5. With clock_config.c from
v2.10, the boards do not work. Refactoring of the clock set-up is on the
to-do list.
- Enable expiry timers for UART, I2C and SPI, avoiding a stall in library
code.
- The clock_config.* files are moved from the board-specific directories to
the boards directory and given a MCU related name.
It's no longer needed because this macro is now processed after
preprocessing the source code via cpp (in the qstr extraction stage), which
means unused MP_REGISTER_MODULE's are filtered out by the preprocessor.
Signed-off-by: Damien George <damien@micropython.org>
This cleans up the parsing of MP_REGISTER_MODULE() and generation of
genhdr/moduledefs.h so that it uses the same process as compressed error
string messages, using the output of qstr extraction.
This makes sure all MP_REGISTER_MODULE()'s that are part of the build are
correctly picked up. Previously the extraction would miss some (eg if you
had a mod.c file in the board directory for an stm32 board).
Build speed is more or less unchanged.
Thanks to @stinos for the ports/windows/msvc/genhdr.targets changes.
Signed-off-by: Damien George <damien@micropython.org>
The following changes are made:
- Use software SPI for external SPI flash access when building mboot.
- Enable the mboot filesystem-loading feature, with FAT FS support.
- Increase the frequency of the CPU when in mboot to 96MHz, to increase the
speed of SPI flash accesses and programming.
Signed-off-by: Damien George <damien@micropython.org>
This allows a board to modify initial_r0 if needed.
Also make default board behaviour functions always available, named as
mboot_get_reset_mode_default and mboot_state_change_default.
Signed-off-by: Damien George <damien@micropython.org>
I2C transfers are much more efficient if they are combined, instead of
doing separate writes and reads.
Fixes issue #7134.
Signed-off-by: Damien George <damien@micropython.org>
This follows on from a5324a1074 and allows
mpy-cross to dynamically select whether ARMv7-M instructions are supported
in @micropython.asm_thumb functions.
The config option MICROPY_EMIT_INLINE_THUMB_ARMV7M is no longer needed, it
is now controlled by MICROPY_EMIT_THUMB_ARMV7M.
Signed-off-by: Damien George <damien@micropython.org>
For ports with MICROPY_VFS and MICROPY_PY_IO enabled their configuration
can now be simplified to use the defaults for mp_import_stat and
mp_builtin_open.
This commit makes no functional change, except for the following minor
points:
- the built-in "open" is removed from the minimal port (it previously did
nothing)
- the duplicate built-in "input" is removed from the esp32 port
- qemu-arm now delegates to VFS import/open
Signed-off-by: Damien George <damien@micropython.org>
Damien George