CCaches are scoped per-job.
Uses https://github.com/hendrikmuhs/ccache-action to get desired behaviour
(updating the cache on each run).
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Allows splitting the esp32 job into multiple parts without too much
boilerplate. The matrix is parameterised using the name of the function to
call in tools/ci.sh, to minimise the dependency on GitHub Actions.
This can get esp32 build times down around 3m if IDF is cached already.
If the cache is cold, the cache preparation step on each job can double up
against each other. However, restructuring the workflow to not do this
seems either complex or requires copy-pasting the entire cache step.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Cache is keyed on the ESP-IDF version used in CI, so there shouldn't be any
cache invalidation issues when ESP-IDF version changes.
Restoring from cache takes approx 15s, compared to 2-3m to perform these
steps (ESP-IDF tools install, ESP-IDF clone, ESP-IDF submodule clone) the
first time.
Cache size is approx 1.6GB, the git clone is tweaked as much as possible to
keep the size down.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Configures the I2S PLL to produce a frequency that the I2S clock generator
can use to create an optimal SCK frequency. The I2S PLL configuration
table is automatically generated at build time.
Fixes issue #10280.
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
This board has MICROPY_VFS enabled, which should take precedence over
MICROPY_MBFS (and did prior to 22d9116c8c).
Signed-off-by: Damien George <damien@micropython.org>
All ports using this common configuration already enable time/date
validation, so this commit is a no-op change.
Signed-off-by: Damien George <damien@micropython.org>
Also move MICROPY_PY_PENDSV_ENTER/REENTER/EXIT to mphalport.h, for ports
where these are not already there.
This helps separate the hardware implementation of these macros from the
MicroPython configuration (eg for renesas-ra and stm32, the IRQ static
inline helper functions can now be moved to irq.h).
Signed-off-by: Damien George <damien@micropython.org>
MICROPY_BEGIN_ATOMIC_SECTION/MICROPY_END_ATOMIC_SECTION belong more to the
MicroPython HAL rather than build configuration settings, so move their
default configuration to py/mphal.h, and require all users of these macros
to include py/mphal.h (here, py/objexcept.c and py/scheduler.c).
This helps ports separate configuration from their HAL implementations, and
can improve build times (because mpconfig.h is included everywhere, whereas
mphal.h is not).
Signed-off-by: Damien George <damien@micropython.org>
Changes:
- os.uname() is removed to save space; sys.version and sys.implementation
can be used instead.
- os.sync() now uses the common extmod version and syncs by calling the FAT
FS sync function, which eventually calls sflash_disk_flush().
Signed-off-by: Damien George <damien@micropython.org>
The os.dupterm() function has changed on this port, it now matches the
semantics used by all other ports (except it's restricted to accept only
machine.UART objects).
Signed-off-by: Damien George <damien@micropython.org>
Now that the MICROPY_BEGIN_ATOMIC_SECTION/MICROPY_END_ATOMIC_SECTION macros
act the same as disable_irq/enable_irq, it's possible to use the common
extmod implementation of these machine functions.
Signed-off-by: Damien George <damien@micropython.org>
This commit changes the cc3200 port to use the common machine
implementation of machine.disable_irq() and machine.enable_irq(). This
eliminates its dependency on the stm32 port's code. The behaviour of
cc3200 for these functions is changed:
- disable_irq() now returns an (opaque) integer rather than a bool
- enable_irq(state) must be passed and argument, which is the return value
of disable_irq() rather than a bool
Signed-off-by: Damien George <damien@micropython.org>
The ports esp32, mimxrt, rp2 and samd all shared exactly the same
implementation of machine.disable_irq() and machine.enable_irq(),
implemented in terms of MICROPY_{BEGIN,END}_ATOMIC_SECTION. This commit
factors these implementations into extmod/modmachine.c.
The cc3200, esp8266, nrf, renesas-ra and stm32 ports do not yet use this
common implementation.
Signed-off-by: Damien George <damien@micropython.org>
Minor changes for consistency are:
- nrf gains: unique_id(), freq() [they do nothing]
- samd: deepsleep() now resets after calling lightsleep()
- esp32: lightsleep()/deepsleep() no longer take kw arg "sleep", instead
it's positional to match others. also, passing 0 here will now do a 0ms
sleep instead of acting like nothing was passed.
reset_cause() no longer takes any args (before it would just ignore them)
- mimxrt: freq() with an argument and lightsleep() both raise
NotImplementedError
Signed-off-by: Damien George <damien@micropython.org>
And use it in all ports. The ports are unchanged, except esp8266 which now
just returns None from this function instead of the time elapsed (to match
other ports), and qemu-arm which gains this function.
Signed-off-by: Damien George <damien@micropython.org>
This is a code factoring to have the dict for the machine module in one
location, and all the ports use that same dict. The machine.soft_reset()
function implementation is also factored because it's the same for all
ports that did already implement it. Eventually more functions/bindings
can be factored.
All ports remain functionally the same, except:
- cc3200 port: gains soft_reset, mem8, mem16, mem32, Signal; loses POWER_ON
(which was a legacy constant, replaced long ago by PWRON_RESET)
- nrf port: gains Signal
- qemu-arm port: gains soft_reset
- unix port: gains soft_reset
- zephyr port: gains soft_reset, mem8, mem16, mem32
Signed-off-by: Damien George <damien@micropython.org>
Prior to this change, if a board did not define any hardware I2C pins, via
MICROPY_HW_I2Cx_SCL, then machine.I2C would alias to machine.SoftI2C.
That doesn't really make sense, and SoftI2C should always be used if there
is no hardware implementation. So this commit makes it so that machine.I2C
is only available if at least one set of I2C hardware pins are defined via
the MICROPY_HW_I2Cx_SCL/SDA macros.
For all boards that define at least one set of I2C hardware pins (which is
most of them) this commit is a no-op. The only boards that change are:
LEGO_HUB_NO6, LEGO_HUB_NO7, STM32H7B3I_DK.
Signed-off-by: Damien George <damien@micropython.org>
MICROPY_PY_MACHINE_SPI is defined in mpconfigport.h to be equal to
MICROPY_PY_MACHINE_HW_SPI, so they are equivalent options. The former one
is preferred because it's used by all other ports.
The default in mpconfigport.h is to enable this option, and all boards that
enable SPI have this removed from their mpconfigboard.h file so they pick
up the default.
Signed-off-by: Damien George <damien@micropython.org>
best_effort_wfe_or_timeout() already calls time_reached() and returns the
result of it, so no need to call it again.
Signed-off-by: Damien George <damien@micropython.org>
If a port defines MICROPY_SOFT_TIMER_TICKS_MS then soft_timer assumes a
SysTick back end, and provides a soft_timer_next variable that sets when
the next call to soft_timer_handler() should occur.
Otherwise, a port should provide soft_timer_get_ms() and
soft_timer_schedule_at_ms() with appropriate semantics (see comments).
Existing users of soft_timer should continue to work as they did.
Signed-off-by: Damien George <damien@micropython.org>
This allows e.g. a board (or make command line) to set
MICROPY_MANIFEST_MY_VARIABLE = path/to/somewhere
set(MICROPY_MANIFEST_MY_VARIABLE path/to/somewhere)
and then in the manifest.py they can query this, e.g. via
include("$(MY_VARIABLE)/path/manifest.py")
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Commit 7ea06a3e26 moved the
`rmt_write_items()` call to fix RMT looping for ESP32-S3, but broke it for
the other ESP32s. This commit conditionally compiles the location of that
call.
Signed-off-by: Mark Blakeney <mark.blakeney@bullet-systems.net>
Prior to this change, after calling connect() the status() method for the
STA interface would either return STAT_GOT_IP or STAT_CONNECTION. The
latter would be returned because wifi_sta_connect_requested==true and
conf_wifi_sta_reconnects==0 by default. As such there was no way to know
anything about errors when attempting to connect, such as a bad password.
Now, status() can return STAT_NO_AP_FOUND and STAT_WRONG_PASSWORD when
those conditions are met.
Fixes issue #12930.
Signed-off-by: IhorNehrutsa <Ihor.Nehrutsa@gmail.com>
In ESP-IDF, enabling SPIRAM in menuconfig sets some Kconfig options:
- "Wi-Fi Cache TX Buffers" enabled. By default this tries to allocate 32 of
these when Wi-Fi is initialised, which requires 54,400 bytes of free heap.
- Switches "Type of WiFi TX buffers" from Dynamic to Static. This
pre-allocates all of the Wi-Fi transmit buffers.
Not a problem if PSRAM is initialised, but it's quite a lot of RAM if PSRAM
failed to initialise! As we use the same config for PSRAM & no-PSRAM builds
now, this either causes Wi-Fi to fail to initialise (seen on S2) or will
eat quite a lot of RAM.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
In commit 7c929d44 the console UART was changed to use the UART HAL.
Starting the UART HAL will change the UART clock from whatever it was
already configured at to UART_SCLK_DEFAULT. There is no "initialize at
existing settings" option.
This clock doesn't work with DFS.
The ESP-IDF code already takes this into account, and when DFS is enabled
it will configure the console UART to use the correct platform-specific
clock that will work with DFS.
The UART HAL init undoes this and sets it back to default.
This change will query the clock before the HAL init, then use the HAL
function to restore it back. Thus keeping the clock at the "correct"
value, which depends on platform, DFS status, and so on.
The clock frequency will be found using the UART driver function ESP-IDF
code uses for this. The existing code hard-coded a path that worked if the
clock was the APB clock and would fail otherwise.
The UART_NUM_0 define is removed because driver/uart.h already provides
this same macro.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Angus Gratton