mirror
/
GRBL-Advanced
kopia lustrzana https://github.com/Schildkroet/GRBL-Advanced
1
0
Forkuj 0
Kod Zgłoszenia Packages Projekty Wydania Wiki Aktywność
This version of Grbl runs on a STM32F411RE / STM32F446RE Nucleo Board
26 Commity
3 Gałęzie
2 Tagi
5,1 MiB
C 99.4%
Assembly 0.4%
Makefile 0.2%
 
 
 
Go to file
Schildkroet 5d3d1c71ee
Fixed not cleared serial buffer after soft reset 		2018-11-18 12:59:06 +01:00
HAL Several code changes and improvements 2018-11-07 19:00:32 +01:00
SPL Initial commit 2017-05-31 00:12:10 +02:00
Src Several code changes and improvements 2018-11-07 19:00:32 +01:00
cmsis Initial commit 2017-05-31 00:12:10 +02:00
grbl Bugfix in backlash compensation because of overrunning planner buffer 2018-11-07 20:56:47 +01:00
.gitignore Initial commit 2017-05-31 00:12:10 +02:00
GRBL_Advanced.ebp Several code changes and improvements 2018-11-07 19:00:32 +01:00
GRBL_Advanced.elay Several code changes and improvements 2018-11-07 19:00:32 +01:00
LICENSE Initial commit 2017-05-31 00:07:26 +02:00
Makefile Increased buffer sizes, makefile improvements 2018-05-24 18:12:04 +02:00
README.md Updated readme 2018-05-23 18:40:59 +02:00
main.c Fixed not cleared serial buffer after soft reset 2018-11-18 12:59:06 +01:00
nucleof411re_pinout.png Initial commit 2017-05-31 00:12:10 +02:00
stm32f411re_flash.ld Initial commit 2017-05-31 00:12:10 +02:00

README.md

Grbl-Advanced is a no-compromise, high performance, low cost alternative for CNC milling. This version of Grbl-Advanced runs on a STM32F411 Nucleo Board.

It accepts standards-compliant g-code and has been tested with the output of several CAM tools with no problems. Arcs, circles and helical motion are fully supported, as well as, all other primary g-code commands. Macro functions, variables, and most canned cycles are not supported, but we think GUIs can do a much better job at translating them into straight g-code anyhow.

Grbl-Advanced includes full acceleration management with look ahead. That means the controller will look up to 16 motions into the future and plan its velocities ahead to deliver smooth acceleration and jerk-free cornering.

  • Built on the wonderful Grbl v1.1 (2017) firmware written by Sungeun "Sonny" Jeon, Ph.D. (USA).

Build Environment:

EmBitz 1.11

Hardware:

  • STM32 Nucleo F411RE
  • STM32F411RET6 in LQFP64 package
  • ARM®32-bit Cortex®-M4 CPU with FPU
  • 100 MHz max CPU frequency
  • 512 KB Flash
  • 128 KB SRAM

Install:

Windows

  • Download and install EmBitz
  • Open .ebp Project File with EmBitz
  • Select 'Release' Target
  • Hit Compile
  • Flash HEX created in bin/Release

Linux

List of Supported G-Codes in Grbl-Advanced:
  - Non-Modal Commands: G4, G10L2, G10L20, G28, G30, G28.1, G30.1, G53, G92, G92.1
  - Motion Modes: G0, G1, G2, G3, G38.2, G38.3, G38.4, G38.5, G80
  - Feed Rate Modes: G93, G94
  - Unit Modes: G20, G21
  - Distance Modes: G90, G91
  - Arc IJK Distance Modes: G91.1
  - Plane Select Modes: G17, G18, G19
  - Tool Length Offset Modes: G43.1, G49
  - Cutter Compensation Modes: G40
  - Coordinate System Modes: G54, G55, G56, G57, G58, G59
  - Control Modes: G61
  - Program Flow: M0, M1, M2, M30*
  - Coolant Control: M7*, M8, M9
  - Spindle Control: M3, M4, M5
  - Valid Non-Command Words: F, I, J, K, L, N, P, R, S, T, X, Y, Z