wfview/CHANGELOG

475 wiersze
15 KiB
Plaintext

# CHANGELOG
- 20210521
Add baud rate detection for remote rigs
Correct propCIVAddr to work if less than 0xe0
Change audiohandler to use latency for tx audio
- 20210520
Added IC-756 Pro. Tested UI and back-end response with 7300 and fake
RigID reply.
Added additional support for the IC-756 Pro III. Essentially untested.
Cleaned up warning and UI help text.
Add more features to rigstate
- 20210519
Model ID text format fixed. Shows IC-0x followed by the raw rig ID
received.
Fixed issue where unknown rigs were identified as 0xff. All rigs are now
identified using rigCaps.modelID, populated with the raw response from
the Rig ID query. Enumerations of known rig types continue to fall into
rigCaps.model, and unknwn rigs will match to rigCaps.model=modelUnknown,
as before.
Serial baud rate is in the UI now. Added some enable/disable code to
prevent confusion about which options can be used with which types of
connections.
Better about box.
fixed filename in instructions
Add MacOS serial port entitlement
- 20210518
Remove unused variables
Make windows build include git version
Command line version of git must be available in the path.
Various file tidying for Windows/Mac builds
Flush buffers if too many lost packets.
remove duplicate audioPacket metatype
Fix silly error in udpserver audio
Allow receive only in udpHandler
Manual CIV is now read from the preferences and populates the UI
accordingly.
Changed UI a little, and added manual CI-V options. Seems to work well.
- 20210517
Fixes for MacOS build - sandbox
Fixes for mac logging/pty since adding sandbox
Make audio input buffer a qMap
Use qMap instead of qVector for buffers as they are auto-sorted.
- 20210516
Fixed attenuator on IC-7000
register audio metatype in wfmain with all of the others
Move manual serial port so linux/mac only
- 20210516 Added IC-7200 support. This has not been tested.
- 20210515 Change to correct bug when CI-V is user-specified and rigCaps were never
populated.
Making the s-meter error command easier to read.
Added IC-706 to rigCaps. Support for the IC-706 is currently broken but
development is in progress.
Added check for if the rig has spectrum during initial state queries.
BSR debug code.
Small fixes for rigctld
- 20210514 Make UDP port textboxes expanding.
Selecting an antenna now sets that antenna for TX and RX.
wfview now closes when the main window is closed.
Filter selection now checks for data mode.
Preliminary IC-7000 support. TODO: Input selection, modes, filters,
reported bug with frequency input and s-meter.
Moved the power buttons.
Cyan for the tuning line.
Resize UDP port text boxes (again!)
ake UDP port textboxes expanding.
Fixes to UDP server
Hopefully improve stability of pty by filtering traffic for any other CIV id.
- 20210513 Additional search path for macports compatibility (macOS only).
Slower polling for older rigs using lower serial baud.
Fix CI-V packet length bug in udphandler
Set pty serial port to NULL by default
- 20210512 Fix for crash on MacOS
- 20210511 Fixes for virtual serial port in Windows.
Initial commit of pty rewrite
There is a new combobox in Settings which shows the file that the pty device is mapped to.
You can select from ~/rig-pty[1-8] which should work if you have multiple instances of wfview.
- 20210509 Enhanced accessibility for the UI.
- 20210508 Data Mode now sends the currently selected filter.
Removed -march=native compiler and linker flags. This should make the
binary builds more compatible, and also eliminate an issue on Pop! OS,
where the default optimizations clashed.
Preliminary IC910H support
- 20210507 Added serial port iterators for the IC-7610 and IC-R8600. Untested.
removing debug info we didn't need.
Adding /dev/ to discovered serial devices, also ignoring case on "auto"
for serial port device.
wfview's own memory system now tracks mode correctly. *however*, it
needs work:
It should track the selected filter, since this information is generally
available and useful, and it should also be storing the frequencies in Hz.
I am also not sure how well the stored memory mode specification
will work across multiple rigs.
Added more mode shortcuts: A = airband, $ = 4 meter band (shift-4), W =
WFM, V = 2M, U = 70cm, Shift-S = 23cm (S-band)
Fixed BSR mode and filter selection.
The band stacking register now uses the newer integer frequency parsing.
We also communicate a little slower to the serial rigs, which seems more
reliable.
Updater serialDeviceListCombo with current COM/tty port setting
pttyHandler doesn't use pty parameter in Linux so set to Q_UNUSED to eliminate warning
- 20210506 Force DTR/RTS to false to stop rigs going into TX if USB Send is enabled
Convert project to 32bit default on Windows and remove beginnings of VSPE code.
- 20210505 Add code to select virtual serial port
fixed a typo in mint instructions and ubuntu instructions
- 20210504 fixed the display instead of rigcaps so that ant sel starts with 1 instead of 0
Fix to add a blank user line in server if no users are configured.
small changes where to find the release; removed the src/build target directory requirement as the release unpacks in ./dist
- 20310503 Fix for Built-in audio on MacOS
- 20210501 Fixed bug 007, which allowed negative frequencies to be dialed.
Double-clicking the waterfall now obeys the tuning step and rounding
option in the settings.
Unified frequency-type MHz to use same code as Hz.
Add WFM mode for IC705 and remove duplicate WFM mode for IC-R8600
make bandType start at 0 so it doesn't overflow rigCaps.bsr
Fix windows release build
Changed the organization and domain to wfview and wfview.org.
Added more modes for the IC-R8600.
- 20210430 Different timing on command polling for serial rigs.
- 20210427 Minor changes to hide sat button until we have time to work on that
feature.
Additional bands added, Airband, WFM
added 630/2200m for 705; probably like the 7300 hardly useable for TX though. Also added auomatic switching to the view pane after non-BSR bands are selected
added 630/2200m to 7300/7610/785x
derp: fixed main dial freq display for non-BSR 4m band; see also previous commit
fixed main dial freq display for non-BSR bands 60, 630, 2200m if such a band was selected in the band select menu
Minor change to set frequency, which was lacking "emit" at the start.
changed the modeSelectCombo-addItem sequence a bit to have modes grouped; CW and CW-R are now grouped, as well as RTTY/RTTY-R; AM and FM are grouped now
- 20210426 Well, that was fun. Color preferences now work, and colors can be
modified from the preference file for custom plot colors.
The preference file now stores colors as unsigned int. To convert the
colors in the file to standard AARRGGBB format (AA = Alpha channel), use
python's hex() function. Maybe one day we will fix the qt bug and make
this save in a better format.
Added dynamic band buttons. Fixed multiple bugs related to various
differences in band stacking register addresses (for example, the GEN
band on the 705 has a different address from the 7100 and the 7300).
This code was only tested with the 9700.
started rough docs for the usermanual
- 20210425 More work on rigctld
Faster polling. Clarified in comments around line 309 in wfmain.cpp.
Added ability to read RIT status. Added RIT to initial rig query. Added
Added ability to read RIT status. Added RIT to initial rig query. Added
variables to handle delayed command timing values. Fixed bug in
frequency parsing code that had existed for some time. Changed tic marks
on RIT knob because I wanted more of them. Bumped startup initial rig
state queries to 100ms. May consider faster queries on startup since we
are going to need more things queried on startup.
- 20210424 Receiver Incremental Tuning is in. The UI does not check the rig's
initial state yet, but the functions are partially in rigCommander for
that purpose.
- 20210423 Found two missing defaults in switch cases inside rigcommander.cpp.
Modified rig power management to stop command ques (s-meter and others).
Upon rig power up, the command queue is repurposed as a 3 second delay
for bootup, and then, commands are issued to restore the spectrum
display (if the wf checkbox was checked). I've made new functions,
powerRigOff and powerRigOn, for these purposes.
work in progress on spectrum enable after power off/on.
powerOff should work now.
- 20210420 rigctl working (sort of) with WSJT-X
- 20210419 Initial commit of rigctld (doesn't currently do anything useful!)
- 20210417 Adding a default position for the frequency indicator line.
Goodbye tracer
- 20210416 added support info for prebuild-systems
- 20210412 added airband, dPMR, lw/mw European and fast HF/70/23cm 1 MHz tuning steps
- 20210411 Added ATU feature on 7610.
Now grabs scope state on startup. Found bug, did not fix, in the
frequency parsing code. Worked aroud it by using doubles for now.
- 20210410 Preamp and attenuator are now queried on startup. Additionally, the
preamp is checked when the attenuator is changed, and the attenuator is
checked with the preamp is changed. This helps the user understand if
the rig allows only one or the other to be active (such as the IC-9700).
Added frequency line. Let's see how we like it.
Add some preliminary parts of getting the attenuator, preamp, and
antenna selection on startup. UI not updated yet but getting there.
- 20210409 Moved ATU controls to main tab.
Added waterfall theme combo box
Removed buttons from attenuator preamp UI controls.
Antenna selection might work, untested.
Preamp code is in. Can't read the current preamp state yet but we can
set it. Nicer names for preamp and attenuator menu items.
- 20210408 Preamp data is now tracked (but not used yet)
re-added lost tooptip for SQ slider
- 20210407 Minor disconnect in the getDTCS call
Attenuators are in! Please try them out!
- 20210406 The repeater setup now disables elements for things your rig doesn't do.
We now query the repeater-related things on startup, such that the
repeater UI is populated correctly.
We now have kHz as the assumed input format if there isn't a dot in the
entry box. Enjoy that!
Minor change so that we track the selected tone to mode changes, keeping
the radio in sync with the UI.
Tone, Tone Squelch, and D(T)CS seem to work as expected. Mode can be
selected.
- 20210405 removed 150 Hz CTCSS / NATO as it can't make that by itself
added 77.0 Hz tone to CTCSS
We can now read the repeater access mode and update the UI. What remains
is to be able to set the mode.
Working read/write of Tone, TSQL, and DTCS tones/code. Some code is also
present now to change the mode being used (tone, tsql, DTCS, or some
combo of the two).
- 20210404 Tone, TSQL, and DTCS code added, but not complete.
better tone mode names
Started work on the tone mode interface.
- 20210401 Added placeholders for attenuator, preamp, and antenna selection UI
controls.
Moved some repeater-related things out from rig commander and into a
shared header.
- 20210331 Adjusting signals and slots for repeater duplex.
Basic duplex code copied from wfmain to the new repeatersetup window.
- 20210330 Added conditional to debug on serial data write size.
- 20210329 Fix crash when radio is shutdown while wfview is connected.
- 20210311 Add local volume control for UDP connections.
add volume control to audiohandler
Small fixes to UDP server
Add USB audio handling to UDP server
Changed frequency parameters to (mostly) unsigned 64-bit ints. This
makes all the rounding code very simple and removes many annoying lines
of code designed to handle errors induced by using doubles for the
frequency.
- 20210310 audio resampling added / opus
updates on virtual serial port
fixed input combo boxes from growing
fixed 4:15 rollover/disconnect issue
- 20210304 Tuning steps! Still need to zero out those lower digits while scrolling
if box is checked.
Fix spectrum peaks as well.
Fix spectrum 'flattening' with strong signal
Add separate mutex for udp/buffers.
supported rigs IC705, IC7300 (over USB, no sound), IC7610, IC785x
- 20210227 changed the way udp audio traffic is handled
on both the TX and RX side.
- 20210226 Fixed minor bug where flock did not stop double-clicking on the
spectrum.
S-meter ballistics:
Turned up the speed. Once you see fast meters, there's no going back.
Tested at 5ms without any issues, comitting at 10ms for now. Note that
50ms in the first 'fixed' meter code is the same as 25ms now due to how
the command queue is structured. So 10ms is only a bit faster than
before.
Fixed meter polling issue
- 20210224 fixed 785x lockup
Added scale and dampening/averaging to s-meter
- 20210222 f-lock works now
- 20210221 added working s-meter
added working power meter
added visual studio 2019 solution (windows builds)
changed packet handling, WIP
rigtype stays in view on status bar
added audio input gain slider
- 20210218
added SQ slider
added TX power slider
added TX button
added simplex/duplex/auto shifts
added debug logging
added TX and RX codec selections
added RX audio buffer size slider
started adding server setup
- 20210210 added control over LAN for rigs that support it
has been tested on the 705, 7610, 785x, 9700.
should work on 7700, 7800, other rigs.
added different sampling rates for rx
added different codecs
added scope data for 7610, 785x.
several cosmetic changes in the UI
fixed a slew of bugs
builds on MAC-OS, Linux, Windows
added ToFixed
implemented connect/disconnect rig
improved USB serial code
fixed memory leak
redesigned rx audio path for better performance
added round trip time for network connected devices
added detection code of rigtype
automatic detection of CIV control address
added logfile capability
works on a raspberry pi (USB and ethernet)