kopia lustrzana https://github.com/micropython/micropython
74 wiersze
3.5 KiB
C
74 wiersze
3.5 KiB
C
/* This file is part of the MicroPython project, https://micropython.org/
|
|
* MIT License; Copyright (c) 2021 Damien P. George
|
|
*/
|
|
|
|
#define MICROPY_HW_BOARD_NAME "NUCLEO-WL55"
|
|
#define MICROPY_HW_MCU_NAME "STM32WL55JCI7"
|
|
|
|
#define MICROPY_EMIT_THUMB (0)
|
|
#define MICROPY_EMIT_INLINE_THUMB (0)
|
|
#define MICROPY_PY_BUILTINS_COMPLEX (0)
|
|
#define MICROPY_PY_GENERATOR_PEND_THROW (0)
|
|
#define MICROPY_PY_MATH (0)
|
|
#define MICROPY_PY_FRAMEBUF (0)
|
|
#define MICROPY_PY_SOCKET (0)
|
|
#define MICROPY_PY_NETWORK (0)
|
|
#define MICROPY_PY_ONEWIRE (0)
|
|
#define MICROPY_PY_STM (1)
|
|
#define MICROPY_PY_PYB_LEGACY (0)
|
|
#define MICROPY_PY_HEAPQ (0)
|
|
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_ADC (0) // use machine.ADC instead
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
|
|
// There is an external 32kHz oscillator
|
|
#define MICROPY_HW_RTC_USE_LSE (1)
|
|
#define MICROPY_HW_RTC_USE_US (1)
|
|
|
|
// Use external 32MHz TCXO + PLL as system clock source
|
|
// (If unset, board will use the internal MSI oscillator instead.)
|
|
#define MICROPY_HW_CLK_USE_HSE (1)
|
|
|
|
// HSE bypass for STM32WL5x means TCXO is powered from PB0_VDDTCXO pin
|
|
#define MICROPY_HW_CLK_USE_BYPASS (1)
|
|
|
|
// UART buses
|
|
#define MICROPY_HW_UART1_TX (pin_B6) // Arduino D1, pin 7 on CN9
|
|
#define MICROPY_HW_UART1_RX (pin_B7) // Arduino D0, pin 8 on CN9
|
|
#define MICROPY_HW_LPUART1_TX (pin_A2) // ST-link
|
|
#define MICROPY_HW_LPUART1_RX (pin_A3) // ST-link
|
|
#define MICROPY_HW_UART_REPL PYB_LPUART_1
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
// I2C buses
|
|
#define MICROPY_HW_I2C1_SCL (pin_A12) // Arduino D15, pin 10 on CN5
|
|
#define MICROPY_HW_I2C1_SDA (pin_A11) // Arduino D14, pin 9 on CN5
|
|
#define MICROPY_HW_I2C3_SCL (pin_B13) // Arduino A5, pin 6 on CN8
|
|
#define MICROPY_HW_I2C3_SDA (pin_B14) // Arduino A4, pin 5 on CN8
|
|
|
|
// SPI buses
|
|
#define MICROPY_HW_SPI1_NSS (pin_A4) // Arduino D10 pin 3 on CN5
|
|
#define MICROPY_HW_SPI1_SCK (pin_A5) // Arduino D13, pin 6 on CN5
|
|
#define MICROPY_HW_SPI1_MISO (pin_A6) // Arduino D12, pin 5 on CN5
|
|
#define MICROPY_HW_SPI1_MOSI (pin_A7) // Arduino D11, pin 4 on CN5
|
|
|
|
// SUBGHZSPI Internal radio SPI BUS
|
|
#define MICROPY_HW_SUBGHZSPI_NAME "SUBGHZ"
|
|
#define MICROPY_HW_SUBGHZSPI_ID 3
|
|
|
|
// User switch; pressing the button makes the input go low
|
|
#define MICROPY_HW_USRSW_PIN (pin_A0)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
|
|
#define MICROPY_HW_USRSW_PRESSED (0)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_B15) // blue
|
|
#define MICROPY_HW_LED2 (pin_B9) // green
|
|
#define MICROPY_HW_LED3 (pin_B11) // red
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|