The actual underlying error number raised from the lwIP subsystem when
attempting to listen on a socket is swallowed and replaced with an
out-of-memory error which is confusing.
This commit passes the underlying error message from the lwIP subsystem to
the appropriate OSError exception.
Most of the content of README.md became obsolete and was replaced by the
documentation of MicroPython. Instead, README.md now shows build
instructions like the other ports.
Including the uasyncio scripts and the drivers for DHT, DS18x20 and
onewire. The uasyncio scripts need about 8k of flash and are not included
for the SAMD21 boards by default.
This prevents a very subtle bug caused by writing e.g. `bytearray('\xfd')`
which gives you `(0xc3, 0xbd)`.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
There are two calls to mp_builtin___import__():
1. ports/unix/main.c:main_() which provides a str in args[0]
2. py/runtime.c:mp_import_name() which provides a qstr in args[0]
The default implementation of mp_builtin___import__() is
mp_builtin___import___default() which has a different implementation based
on MICROPY_ENABLE_EXTERNAL_IMPORT.
If MICROPY_ENABLE_EXTERNAL_IMPORT is disabled then the handling of weak
links assumes that args[0] is a `const char *`, when it is either a str or
qstr object.
Use the existing qstr of the module name instead, and also use a vstr
instead of strcpy() to ensure no overflow occurs.
Emscripten strongly advises the use of optimisation when compiling with
ASYNCIFY enabled. Testing the difference betwen O3 and Os for various
configurations gives:
flags firmware.wasm micropython.js perf
-O3 -s ASYNCIFY 1342003 212845 0 (baseline)
-O3 -s ASYNCIFY -s WASM=0 - 7064750 -30%
-O3 367131 196569 +140%
-O3 -s WASM=0 - 2818260 +30%
-Os -s ASYNCIFY 1135450 213064 +40%
-Os -s ASYNCIFY -s WASM=0 - 6239768 -30%
-Os 295028 196569 +180%
-Os -s WASM=0 - 2271358 +30%
The first row is prior to this commit. The second and third columns show
firmware size (add them to get the total size). The fourth column shows
the approximate change in performance compared to the baseline. The
performance was measured using run-perfbench.py and the error was large, up
to 20%, although general trends in the change in performance could still be
seen.
In summary, using using Os instead of O3 makes it a little bit faster in
all cases, and smaller output (wasm/js) in all cases.
Signed-off-by: Damien George <damien@micropython.org>
This simplifies the config file. This is not a no-op, it does enable a few
new features to bring the port in line with this config level.
Signed-off-by: Damien George <damien@micropython.org>
So that filesystems mounted with "mpremote mount" can have their files
iterated over, making them consistent with other files.
Signed-off-by: Damien George <damien@micropython.org>
The except handler for OSError didn't include the line that actually calls
os.listdir, so an invalid path wasn't handled correctly.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Checks are added for pwm.freq(), pwm_duty(), pwm_duty_u10() and
pwm.duty_u16(). This avoids a core dump on ESP32C3, and misleading error
messages on Xtensa ESP32 devices.
Set the size of machine_pin_irq_handler array to GPIO_NUM_MAX:
- Min GPIO_NUM_MAX is 22 for IDF_TARGET_ESP32C3.
- Max GPIO_NUM_MAX is 49 for IDF_TARGET_ESP32S3.
The MP_REGISTER_ROOT_POINTER entry must be hard-coded, because the location
that it's evaluated by the compiler does not include the relevant IDF
header to get a definition of GPIO_NUM_MAX.
Each SoC family has its own clocks and timings/timeouts. For I2C, the
default source clock is either APB (ESP32, ESP32-S2) or XTAL (ESP32-S3,
ESP32-C3) as shown in the datasheets. Since
machine_i2c.c/machine_hw_i2c_init() uses the default clk_flags (0), the
alternate low-power clock source is never selected in ESP-IDF
i2c.c/i2c_param_config(). There is not an API in i2c.c to get the source
clock frequency, so a compile-time value is used based on SoC family.
Also, the maximum timeout is different across the SoC families, so use the
I2C_LL_MAX_TIMEOUT constant to eliminate the warning from
i2c_set_timeout().
With these changes, the following results were obtained. The I2C SCL
frequencies were measured with a Saleae logic analyzer.
ESP32 (TTGO T Dislay)
I2C(0, scl=22, sda=21, freq=101781) Measured: 100KHz
I2C(0, scl=22, sda=21, freq=430107) Measured: 400KHz
I2C(0, scl=22, sda=21, freq=1212121) Measured: 941KHz
ESP32-S3 (TTGO T-QT)
I2C(0, scl=34, sda=33, freq=111111) Measured: 107KHz
I2C(0, scl=34, sda=33, freq=444444) Measured: 400KHz
I2C(0, scl=34, sda=33, freq=1111111) Measured: 842KHz
ESP32-C3 (XIAO ESP32C3)
I2C(0, scl=7, sda=6, freq=107816) Measured: 103KHz
I2C(0, scl=7, sda=6, freq=444444) Measured: 380KHz
I2C(0, scl=7, sda=6, freq=1176470) Measured: 800KHz
(ESP32-S2 board was not available for testing.)
So that it doesn't clash with the extmod version.
Also make the default for this enabled, so that most boards do not need to
configure it.
Signed-off-by: Damien George <damien@micropython.org>
This issue affected i.MX RT 1052, 1062 and 1064. It seems to be addressed
by Errata ERR006223, which also mentions i.MX RT101x and 102x, but these
devices worked well even without the change. As a side effect, the current
consumption at an idle REPL drops significantly with this fix.
Fixes issue #7235.
Commit 64af916c11 removed the version string
from docs/conf.py. py/mpconfig.h is a better place to get the version
from, so use that (when there is no git repository).
Signed-off-by: Damien George <damien@micropython.org>
When looking at latest (the default for docs.micropython.org), make it
clear that this isn't the release version.
- Changes the version in the top-left to "latest".
- Adds a message to the top of each page to explain.
For future release versions, add a short message to link to the latest
version.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Protect SerCom (UART, SPI, I2C) objects from getting freed by the GC when
they go out of scope without being deinitialized. Otherwise the ISR of a
Sercom may access an invalid data structure.
Any update of freq or duty_cycle requires the previous PWM cycle to be
finished. Otherwise the new settings are not accepted.
Other changes in this commit:
- Report the set duty cycles even when the PWM is not yet started.
- pwm.freq(0) stops the pwm device, instead of raising an expception.
- Clear the duty cycle value cache on soft reset.
Changes are:
- Remove the LED_Pxxx definitions from pins.csv, now that the LED class is
gone.
- Remove the '-' lines.
- Add default lines for USB and SWCLK, SWDIO.
Jared Hancock