The `_start` function prototype is now declared as no-return, so `main()`
can't return.
To fix this, `main()` is replaced with `_start`.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
If there are any free chunks found then it's better to sweep the filesystem
and use the available chunks, rather than error out with ENOSPC when there
is in fact a bit of space remaining.
Signed-off-by: Damien George <damien@micropython.org>
This allows to follow good practice and have libraries live in the lib
folder which means they will be found by the runtime without adding this
path manually at runtime.
Signed-off-by: Sebastian Romero <s.romero@arduino.cc>
MicroPython code may rely on the return value of sys.stdout.buffer.write()
to reflect the number of bytes actually written. While in most scenarios a
write() operation is successful, there are cases where it fails, leading to
data loss. This problem arises because, currently, write() merely returns
the number of bytes it was supposed to write, without indication of
failure.
One scenario where write() might fail, is where USB is used and the
receiving end doesn't read quickly enough to empty the receive buffer. In
that case, write() on the MicroPython side can timeout, resulting in the
loss of data without any indication, a behavior observed notably in
communication between a Pi Pico as a client and a Linux host using the ACM
driver.
A complex issue arises with mp_hal_stdout_tx_strn() when it involves
multiple outputs, such as USB, dupterm and hardware UART. The challenge is
in handling cases where writing to one output is successful, but another
fails, either fully or partially. This patch implements the following
solution:
mp_hal_stdout_tx_strn() attempts to write len bytes to all of the possible
destinations for that data, and returns the minimum successful write
length.
The implementation of this is complicated by several factors:
- multiple outputs may be enabled or disabled at compiled time
- multiple outputs may be enabled or disabled at runtime
- mp_os_dupterm_tx_strn() is one such output, optionally containing
multiple additional outputs
- each of these outputs may or may not be able to report success
- each of these outputs may or may not be able to report partial writes
As a result, there's no single strategy that fits all ports, necessitating
unique logic for each instance of mp_hal_stdout_tx_strn().
Note that addressing sys.stdout.write() is more complex due to its data
modification process ("cooked" output), and it remains unchanged in this
patch. Developers who are concerned about accurate return values from
write operations should use sys.stdout.buffer.write().
This patch might disrupt some existing code, but it's also expected to
resolve issues, considering that the peculiar return value behavior of
sys.stdout.buffer.write() is not well-documented and likely not widely
known. Therefore, it's improbable that much existing code relies on the
previous behavior.
Signed-off-by: Maarten van der Schrieck <maarten@thingsconnected.nl>
This board has MICROPY_VFS enabled, which should take precedence over
MICROPY_MBFS (and did prior to 22d9116c8c).
Signed-off-by: Damien George <damien@micropython.org>
The os.dupterm() function has changed on this port, it now matches the
semantics used by all other ports (except it's restricted to accept only
machine.UART objects).
Signed-off-by: Damien George <damien@micropython.org>
Minor changes for consistency are:
- nrf gains: unique_id(), freq() [they do nothing]
- samd: deepsleep() now resets after calling lightsleep()
- esp32: lightsleep()/deepsleep() no longer take kw arg "sleep", instead
it's positional to match others. also, passing 0 here will now do a 0ms
sleep instead of acting like nothing was passed.
reset_cause() no longer takes any args (before it would just ignore them)
- mimxrt: freq() with an argument and lightsleep() both raise
NotImplementedError
Signed-off-by: Damien George <damien@micropython.org>
And use it in all ports. The ports are unchanged, except esp8266 which now
just returns None from this function instead of the time elapsed (to match
other ports), and qemu-arm which gains this function.
Signed-off-by: Damien George <damien@micropython.org>
This is a code factoring to have the dict for the machine module in one
location, and all the ports use that same dict. The machine.soft_reset()
function implementation is also factored because it's the same for all
ports that did already implement it. Eventually more functions/bindings
can be factored.
All ports remain functionally the same, except:
- cc3200 port: gains soft_reset, mem8, mem16, mem32, Signal; loses POWER_ON
(which was a legacy constant, replaced long ago by PWRON_RESET)
- nrf port: gains Signal
- qemu-arm port: gains soft_reset
- unix port: gains soft_reset
- zephyr port: gains soft_reset, mem8, mem16, mem32
Signed-off-by: Damien George <damien@micropython.org>
MICROPY_PY_MACHINE_SPI is defined in mpconfigport.h to be equal to
MICROPY_PY_MACHINE_HW_SPI, so they are equivalent options. The former one
is preferred because it's used by all other ports.
The default in mpconfigport.h is to enable this option, and all boards that
enable SPI have this removed from their mpconfigboard.h file so they pick
up the default.
Signed-off-by: Damien George <damien@micropython.org>
It's not worth the effort to update these ports to use boardgen.py, but
put a note just in case anyone uses this as a reference for a new port.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
All ports now use `--board-csv`, `--prefix`, `--output-souce`,
`--output-header` and no longer write to stdout. This matches the esp32
implementation.
Ports that have an AF input use `--af-csv` (to match `--board-csv`).
Any additional output files are now prefixed with `output-` (e.g.
`--output-af-const`).
Default arguments are removed (all makefiles should always specify all
arguments, using default values is likely an error).
Replaced the `af-defs-cmp-strings` and `hdr-obj-decls` args for stm32 with
just `mboot-mode`. Previously they were set on the regular build, now the
logic is reversed so mboot sets it.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It's not supported on all ports, adds complexity to the build to generate
pins_af.py, and can mostly be replicated just by printing the pin objects.
Remove support for generating pins_af.py from all ports (nrf, stm32,
renesas-ra, mimxrt, rp2).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The output pins.c can be processed for qstrs like any other C file.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This prevents each port Makefile from having to add an explicit rule for
`build-BOARD/pins_BOARD.c`.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The contents of machine_mem.h, machine_i2c.h and machine_spi.h have been
moved into extmod/modmachine.h.
Signed-off-by: Damien George <damien@micropython.org>
The contents of machine_bitstream.h, machine_pinbase.h, machine_pulse.h and
machine_signal.h have been moved into extmod/modmachine.h.
Signed-off-by: Damien George <damien@micropython.org>
The machine_i2c_type, machine_spi_type and machine_timer_type symbols are
already declared in extmod/modmachine.h and should not be declared anywhere
else.
Also move declarations of machine_pin_type and machine_rtc_type to the
common header in extmod.
Signed-off-by: Damien George <damien@micropython.org>
This is a code factoring to have the Python bindings in one location, and
all the ports use those same bindings. For all ports except the two listed
below there is no functional change.
The nrf port has UART.sendbreak() removed, but this method previously did
nothing.
The zephyr port has the following methods added:
- UART.init(): supports setting timeout and timeout_char.
- UART.deinit(): does nothing, just returns None.
- UART.flush(): raises OSError(EINVAL) because it's not implemented.
- UART.any() and UART.txdone(): raise NotImplementedError.
Signed-off-by: Damien George <damien@micropython.org>
No functional change, just code factoring to have the Python bindings in
one location, and all the ports use those same bindings.
Signed-off-by: Damien George <damien@micropython.org>
This commit makes it so that MICROPY_PY_MACHINE_PWM is enabled if at least
one of MICROPY_PY_MACHINE_HW_PWM and/or MICROPY_PY_MACHINE_SOFT_PWM are
enabled. This simplifies the configuration for boards, and fixes DVK_BL652
which enabled PWM without selecting software or hardware implementations.
With this change, DVK_BL652 and EVK_NINA_B1 now enable (hardware) PWM.
Signed-off-by: Damien George <damien@micropython.org>
With public declarations moved to extmod/modmachine.h. It's now mandatory
for a port to define MICROPY_PY_MACHINE_PWM_INCLUDEFILE if it enables
MICROPY_PY_MACHINE_PWM. This follows how extmod/machine_wdt.c works.
All ports have been updated to work with this modified scheme.
Signed-off-by: Damien George <damien@micropython.org>
If a non-string buffer was passed to execfile, then it would be passed
as a non-null-terminated char* to mp_lexer_new_from_file.
This changes mp_lexer_new_from_file to take a qstr instead (as in almost
all cases a qstr will be created from this input anyway to set the
`__file__` attribute on the module).
This now makes execfile require a string (not generic buffer) argument,
which is probably a good fix to make anyway.
Fixes issue #12522.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
That can be caused e.g. by an exception. This feature is implemented in
some way already for the stm32, renesas-ra, mimxrt and samd ports. This
commit adds it for the rp2, esp8266, esp32 and nrf ports. No change for
the cc3200 and teensy ports.
Signed-off-by: robert-hh <robert@hammelrath.com>
This commit:
- Finds a common set of board feature tags and maps existing features to
that reduced set.
- Removes some less-useful board feature tags.
- Ensures all MCUs are specified correctly.
- Ensures all boards have a vendor (and fixes some vendor names).
This is to make the downloads page show a less intimidating set of filters.
Work done in conjunction with Matt Trentini <matt.trentini@gmail.com>.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The asyncio module now has much better CPython compatibility and
deserves to be just called "asyncio".
This will avoid people having to write `from uasyncio import asyncio`.
Renames all files, and updates port manifests to use the new path. Also
renames the built-in _uasyncio to _asyncio.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Following how mkrules.cmake works. This makes it easy for a port to enable
frozen code, by defining FROZEN_MANIFEST in its Makefile.
Signed-off-by: Damien George <damien@micropython.org>
Applies to drivers/examples/extmod/port-modules/tools.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Updates any includes, and references from Makefiles/CMake.
This essentially reverts what was done long ago in commit
136b5cbd76
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
In order to keep "import umodule" working, the existing mechanism is
replaced with a simple fallback to drop the "u".
This makes importing of built-ins no longer touch the filesystem, which
makes a typical built-in import take ~0.15ms rather than 3-5ms.
(Weak links were added in c14a81662c)
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This renames the builtin-modules, such that help('modules') and printing
the module object will show "module" rather than "umodule".
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Updates all `help()` output to use the phrase:
`For online docs please visit http://docs.micropython.org/`
Some ports previously used different wording, some pointed to the wrong
link. Also make all ports use `help.c` for consistency.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
All ports that enable MICROPY_PY_MACHINE_PWM now enable these two
sub-options, so remove these sub-options altogether to force consistency in
new ports that implement machine.PWM.
Signed-off-by: Damien George <damien@micropython.org>
API additions;
- time.sleep() is added
- time.ticks_cpu() is added, but it just returns 0
No API or functional change to existing time functions.
Signed-off-by: Damien George <damien@micropython.org>
Based on extmod/utime_mphal.c, with:
- a globals dict added
- time.localtime wrapper added
- time.time wrapper added
- time.time_ns function added
New configuration options are added for this module:
- MICROPY_PY_UTIME (enabled at basic features level)
- MICROPY_PY_UTIME_GMTIME_LOCALTIME_MKTIME
- MICROPY_PY_UTIME_TIME_TIME_NS
Signed-off-by: Damien George <damien@micropython.org>
iabdalkader