mirror
/
micropython
kopia lustrzana https://github.com/micropython/micropython
1
0
Forkuj 0
Kod Zgłoszenia Projekty Wydania Wiki Aktywność

stm32/qspi: Use MPU to allow access to valid memory-mapped QSPI region. 

The Cortex-M7 CPU will do speculative loads from any memory location that
is not explicitly forbidden.  This includes the QSPI memory-mapped region
starting at 0x90000000 and with size 256MiB.  Speculative loads to this
QSPI region may 1) interfere with the QSPI peripheral registers (eg the
address register) if the QSPI is not in memory-mapped mode; 2) attempt to
access data outside the configured size of the QSPI flash when it is in
memory-mapped mode.  Both of these scenarios will lead to issues with the
QSPI peripheral (eg Cortex bus lock up in scenario 2).

To prevent such speculative loads from interfering with the peripheral the
MPU is configured in this commit to restrict access to the QSPI mapped
region: when not memory mapped the entire region is forbidden; when memory
mapped only accesses to the valid flash size are permitted.
pull/4892/head
Damien George 2019-07-03 00:50:32 +10:00
rodzic eca4115f66
commit 8da39fd182
2 zmienionych plików z 32 dodań i 0 usunięć
Pokaż statystyki Ściągnij plik aktualizacji Ściągnij plik porównania Expand all files Collapse all files

3
ports/stm32/mpu.h
Wyświetl plik

@ -29,6 +29,9 @@
#if defined(STM32F7) || defined(STM32H7)
#define MPU_REGION_ETH (MPU_REGION_NUMBER0)
#define MPU_REGION_QSPI1 (MPU_REGION_NUMBER1)
#define MPU_REGION_QSPI2 (MPU_REGION_NUMBER2)
#define MPU_REGION_QSPI3 (MPU_REGION_NUMBER3)
#define MPU_REGION_SDRAM1 (MPU_REGION_NUMBER4)
#define MPU_REGION_SDRAM2 (MPU_REGION_NUMBER5)

29
ports/stm32/qspi.c
Wyświetl plik

@ -28,11 +28,14 @@
#include "py/mperrno.h"
#include "py/mphal.h"
#include "mpu.h"
#include "qspi.h"
#include "pin_static_af.h"
#if defined(MICROPY_HW_QSPIFLASH_SIZE_BITS_LOG2)
#define QSPI_MAP_ADDR (0x90000000)
#ifndef MICROPY_HW_QSPI_PRESCALER
#define MICROPY_HW_QSPI_PRESCALER 3 // F_CLK = F_AHB/3 (72MHz when CPU is 216MHz)
#endif
@ -49,7 +52,31 @@
#define MICROPY_HW_QSPI_CS_HIGH_CYCLES 2 // nCS stays high for 2 cycles
#endif
static inline void qspi_mpu_disable_all(void) {
// Configure MPU to disable access to entire QSPI region, to prevent CPU
// speculative execution from accessing this region and modifying QSPI registers.
mpu_config_start();
mpu_config_region(MPU_REGION_QSPI1, QSPI_MAP_ADDR, MPU_CONFIG_DISABLE(0x00, MPU_REGION_SIZE_256MB));
mpu_config_end();
}
static inline void qspi_mpu_enable_mapped(void) {
// Configure MPU to allow access to only the valid part of external SPI flash.
// The memory accesses to the mapped QSPI are faster if the MPU is not used
// for the memory-mapped region, so 3 MPU regions are used to disable access
// to everything except the valid address space, using holes in the bottom
// of the regions and nesting them.
// At the moment this is hard-coded to 2MiB of QSPI address space.
mpu_config_start();
mpu_config_region(MPU_REGION_QSPI1, QSPI_MAP_ADDR, MPU_CONFIG_DISABLE(0x01, MPU_REGION_SIZE_256MB));
mpu_config_region(MPU_REGION_QSPI2, QSPI_MAP_ADDR, MPU_CONFIG_DISABLE(0x0f, MPU_REGION_SIZE_32MB));
mpu_config_region(MPU_REGION_QSPI3, QSPI_MAP_ADDR, MPU_CONFIG_DISABLE(0x01, MPU_REGION_SIZE_16MB));
mpu_config_end();
}
void qspi_init(void) {
qspi_mpu_disable_all();
// Configure pins
mp_hal_pin_config_alt_static_speed(MICROPY_HW_QSPIFLASH_CS, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, MP_HAL_PIN_SPEED_VERY_HIGH, STATIC_AF_QUADSPI_BK1_NCS);
mp_hal_pin_config_alt_static_speed(MICROPY_HW_QSPIFLASH_SCK, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, MP_HAL_PIN_SPEED_VERY_HIGH, STATIC_AF_QUADSPI_CLK);
@ -100,6 +127,8 @@ void qspi_memory_map(void) {
| 1 << QUADSPI_CCR_IMODE_Pos // instruction on 1 line
| 0xeb << QUADSPI_CCR_INSTRUCTION_Pos // quad read opcode
;
qspi_mpu_enable_mapped();
}
STATIC int qspi_ioctl(void *self_in, uint32_t cmd) {