diff --git a/ports/stm32/boards/NUCLEO_L073RZ/mpconfigboard.h b/ports/stm32/boards/NUCLEO_L073RZ/mpconfigboard.h
new file mode 100644
index 0000000000..ff4be4a277
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_L073RZ/mpconfigboard.h
@@ -0,0 +1,53 @@
+/* This file is part of the MicroPython project, http://micropython.org/
+ * MIT License; Copyright (c) 2019 Damien P. George
+ */
+
+#define MICROPY_HW_BOARD_NAME       "NUCLEO-L073RZ"
+#define MICROPY_HW_MCU_NAME         "STM32F073RZT6"
+
+#define MICROPY_EMIT_THUMB          (0)
+#define MICROPY_EMIT_INLINE_THUMB   (0)
+#define MICROPY_PY_BUILTINS_COMPLEX (0)
+#define MICROPY_PY_MATH             (0)
+#define MICROPY_PY_FRAMEBUF         (0)
+#define MICROPY_PY_USOCKET          (0)
+#define MICROPY_PY_NETWORK          (0)
+#define MICROPY_PY_STM              (0)
+#define MICROPY_PY_PYB_LEGACY       (0)
+#define MICROPY_VFS_FAT             (0)
+
+#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
+#define MICROPY_HW_ENABLE_RTC       (1)
+#define MICROPY_HW_ENABLE_ADC       (0)
+#define MICROPY_HW_HAS_SWITCH       (1)
+
+// UART config
+#define MICROPY_HW_UART1_TX     (pin_B6)
+#define MICROPY_HW_UART1_RX     (pin_B7)
+#define MICROPY_HW_UART2_TX     (pin_A2)
+#define MICROPY_HW_UART2_RX     (pin_A3)
+
+// USART2 is connected to the ST-LINK USB VCP
+#define MICROPY_HW_UART_REPL PYB_UART_2
+#define MICROPY_HW_UART_REPL_BAUD 115200
+
+// I2C busses
+#define MICROPY_HW_I2C1_SCL (pin_B8)        // Arduino D15, pin 3 on CN10
+#define MICROPY_HW_I2C1_SDA (pin_B9)        // Arduino D14, pin 5 on CN10
+
+// SPI busses
+#define MICROPY_HW_SPI1_NSS     (pin_A15)   //              pin 17 on CN7
+#define MICROPY_HW_SPI1_SCK     (pin_A5)    // Arduino D13, pin 11 on CN10
+#define MICROPY_HW_SPI1_MISO    (pin_A6)    // Arduino D12, pin 13 on CN10
+#define MICROPY_HW_SPI1_MOSI    (pin_A7)    // Arduino D11, pin 15 on CN10
+
+// USER B1 has a pull-up and is active low
+#define MICROPY_HW_USRSW_PIN        (pin_C13)
+#define MICROPY_HW_USRSW_PULL       (0)
+#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_FALLING)
+#define MICROPY_HW_USRSW_PRESSED    (0)
+
+// NUCLEO-64 has one user LED
+#define MICROPY_HW_LED1             (pin_A5) // green
+#define MICROPY_HW_LED_ON(pin)      (mp_hal_pin_high(pin))
+#define MICROPY_HW_LED_OFF(pin)     (mp_hal_pin_low(pin))
diff --git a/ports/stm32/boards/NUCLEO_L073RZ/mpconfigboard.mk b/ports/stm32/boards/NUCLEO_L073RZ/mpconfigboard.mk
new file mode 100644
index 0000000000..69601f8602
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_L073RZ/mpconfigboard.mk
@@ -0,0 +1,7 @@
+MCU_SERIES = l0
+CMSIS_MCU = STM32L073xx
+AF_FILE = boards/stm32l072_af.csv
+LD_FILES = boards/stm32l072xz.ld boards/common_basic.ld
+
+# Don't include default frozen modules because MCU is tight on flash space
+FROZEN_MPY_DIR ?=
diff --git a/ports/stm32/boards/NUCLEO_L073RZ/pins.csv b/ports/stm32/boards/NUCLEO_L073RZ/pins.csv
new file mode 100644
index 0000000000..36d3141083
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_L073RZ/pins.csv
@@ -0,0 +1,87 @@
+D0,PA3
+D1,PA2
+D2,PA10
+D3,PB3
+D4,PB5
+D5,PB4
+D6,PB10
+D7,PA8
+D8,PA9
+D9,PC7
+D10,PB6
+D11,PA7
+D12,PA6
+D13,PA5
+D14,PB9
+D15,PB8
+A0,PA0
+A1,PA1
+A2,PA4
+A3,PB0
+A4,PC1
+A5,PC0
+RX,PA3
+TX,PA2
+SCL,PB8
+SDA,PB9
+SCK,PA5
+MISO,PA6
+MOSI,PA7
+CS,PB6
+BOOT0,PF11
+SWDIO,PA13
+SWCLK,PA14
+USER_B1,PC13
+LED_GREEN,PA5
+PA0,PA0
+PA1,PA1
+PA2,PA2
+PA3,PA3
+PA4,PA4
+PA5,PA5
+PA6,PA6
+PA7,PA7
+PA8,PA8
+PA9,PA9
+PA10,PA10
+PA11,PA11
+PA12,PA12
+PA13,PA13
+PA14,PA14
+PA15,PA15
+PB0,PB0
+PB1,PB1
+PB2,PB2
+PB3,PB3
+PB4,PB4
+PB5,PB5
+PB6,PB6
+PB7,PB7
+PB8,PB8
+PB9,PB9
+PB10,PB10
+PB11,PB11
+PB12,PB12
+PB13,PB13
+PB14,PB14
+PB15,PB15
+PC0,PC0
+PC1,PC1
+PC2,PC2
+PC3,PC3
+PC4,PC4
+PC5,PC5
+PC6,PC6
+PC7,PC7
+PC8,PC8
+PC9,PC9
+PC10,PC10
+PC11,PC11
+PC12,PC12
+PC13,PC13
+PC14,PC14
+PC15,PC15
+PD2,PD2
+PF0,PF0
+PF1,PF1
+PF11,PF11
diff --git a/ports/stm32/boards/NUCLEO_L073RZ/stm32l0xx_hal_conf.h b/ports/stm32/boards/NUCLEO_L073RZ/stm32l0xx_hal_conf.h
new file mode 100644
index 0000000000..c88a706510
--- /dev/null
+++ b/ports/stm32/boards/NUCLEO_L073RZ/stm32l0xx_hal_conf.h
@@ -0,0 +1,18 @@
+/* This file is part of the MicroPython project, http://micropython.org/
+ * The MIT License (MIT)
+ * Copyright (c) 2019 Damien P. George
+ */
+#ifndef MICROPY_INCLUDED_STM32L0XX_HAL_CONF_H
+#define MICROPY_INCLUDED_STM32L0XX_HAL_CONF_H
+
+#include "boards/stm32l0xx_hal_conf_base.h"
+
+// Oscillator values in Hz
+#define HSE_VALUE (8000000)
+#define LSE_VALUE (32768)
+
+// Oscillator timeouts in ms
+#define HSE_STARTUP_TIMEOUT (100)
+#define LSE_STARTUP_TIMEOUT (5000)
+
+#endif // MICROPY_INCLUDED_STM32L0XX_HAL_CONF_H