mirror
/
micropython
kopia lustrzana https://github.com/micropython/micropython
1
0
Forkuj 0
Kod Zgłoszenia Projekty Wydania Wiki Aktywność

stm32/qspi: Set pin speed to very-high and allow to config some options. 

The default speed of the QSPI interface is 72Mhz whereas the standard AF
pin speed (high) is only rated to 50Mhz, so increase speed to very-high.
pull/4592/head
Andrew Leech 2019-03-01 13:39:44 +11:00 zatwierdzone przez Damien George
rodzic 2ed2ec1711
commit 0c60cb1fc4
2 zmienionych plików z 30 dodań i 10 usunięć
Pokaż statystyki Ściągnij plik aktualizacji Ściągnij plik porównania Expand all files Collapse all files

4
ports/stm32/mboot/mphalport.h
Wyświetl plik

@ -39,6 +39,10 @@
#define MP_HAL_PIN_PULL_NONE (GPIO_NOPULL)
#define MP_HAL_PIN_PULL_UP (GPIO_PULLUP)
#define MP_HAL_PIN_PULL_DOWN (GPIO_PULLDOWN)
#define MP_HAL_PIN_SPEED_LOW (GPIO_SPEED_FREQ_LOW)
#define MP_HAL_PIN_SPEED_MEDIUM (GPIO_SPEED_FREQ_MEDIUM)
#define MP_HAL_PIN_SPEED_HIGH (GPIO_SPEED_FREQ_HIGH)
#define MP_HAL_PIN_SPEED_VERY_HIGH (GPIO_SPEED_FREQ_VERY_HIGH)
#define mp_hal_pin_obj_t uint32_t
#define mp_hal_pin_input(p) mp_hal_pin_config((p), MP_HAL_PIN_MODE_INPUT, MP_HAL_PIN_PULL_NONE, 0)

36
ports/stm32/qspi.c
Wyświetl plik

@ -33,21 +33,37 @@
#if defined(MICROPY_HW_QSPIFLASH_SIZE_BITS_LOG2)
#ifndef MICROPY_HW_QSPI_PRESCALER
#define MICROPY_HW_QSPI_PRESCALER 3 // F_CLK = F_AHB/3 (72MHz when CPU is 216MHz)
#endif
#ifndef MICROPY_HW_QSPI_SAMPLE_SHIFT
#define MICROPY_HW_QSPI_SAMPLE_SHIFT 1 // sample shift enabled
#endif
#ifndef MICROPY_HW_QSPI_TIMEOUT_COUNTER
#define MICROPY_HW_QSPI_TIMEOUT_COUNTER 0 // timeout counter disabled (see F7 errata)
#endif
#ifndef MICROPY_HW_QSPI_CS_HIGH_CYCLES
#define MICROPY_HW_QSPI_CS_HIGH_CYCLES 2 // nCS stays high for 2 cycles
#endif
void qspi_init(void) {
// Configure pins
mp_hal_pin_config_alt_static(MICROPY_HW_QSPIFLASH_CS, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, STATIC_AF_QUADSPI_BK1_NCS);
mp_hal_pin_config_alt_static(MICROPY_HW_QSPIFLASH_SCK, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, STATIC_AF_QUADSPI_CLK);
mp_hal_pin_config_alt_static(MICROPY_HW_QSPIFLASH_IO0, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, STATIC_AF_QUADSPI_BK1_IO0);
mp_hal_pin_config_alt_static(MICROPY_HW_QSPIFLASH_IO1, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, STATIC_AF_QUADSPI_BK1_IO1);
mp_hal_pin_config_alt_static(MICROPY_HW_QSPIFLASH_IO2, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, STATIC_AF_QUADSPI_BK1_IO2);
mp_hal_pin_config_alt_static(MICROPY_HW_QSPIFLASH_IO3, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, STATIC_AF_QUADSPI_BK1_IO3);
mp_hal_pin_config_alt_static_speed(MICROPY_HW_QSPIFLASH_CS, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, MP_HAL_PIN_SPEED_VERY_HIGH, STATIC_AF_QUADSPI_BK1_NCS);
mp_hal_pin_config_alt_static_speed(MICROPY_HW_QSPIFLASH_SCK, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, MP_HAL_PIN_SPEED_VERY_HIGH, STATIC_AF_QUADSPI_CLK);
mp_hal_pin_config_alt_static_speed(MICROPY_HW_QSPIFLASH_IO0, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, MP_HAL_PIN_SPEED_VERY_HIGH, STATIC_AF_QUADSPI_BK1_IO0);
mp_hal_pin_config_alt_static_speed(MICROPY_HW_QSPIFLASH_IO1, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, MP_HAL_PIN_SPEED_VERY_HIGH, STATIC_AF_QUADSPI_BK1_IO1);
mp_hal_pin_config_alt_static_speed(MICROPY_HW_QSPIFLASH_IO2, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, MP_HAL_PIN_SPEED_VERY_HIGH, STATIC_AF_QUADSPI_BK1_IO2);
mp_hal_pin_config_alt_static_speed(MICROPY_HW_QSPIFLASH_IO3, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, MP_HAL_PIN_SPEED_VERY_HIGH, STATIC_AF_QUADSPI_BK1_IO3);
// Bring up the QSPI peripheral
__HAL_RCC_QSPI_CLK_ENABLE();
QUADSPI->CR =
2 << QUADSPI_CR_PRESCALER_Pos // F_CLK = F_AHB/3 (72MHz when CPU is 216MHz)
(MICROPY_HW_QSPI_PRESCALER - 1) << QUADSPI_CR_PRESCALER_Pos
| 3 << QUADSPI_CR_FTHRES_Pos // 4 bytes must be available to read/write
#if defined(QUADSPI_CR_FSEL_Pos)
| 0 << QUADSPI_CR_FSEL_Pos // FLASH 1 selected
@ -55,14 +71,14 @@ void qspi_init(void) {
#if defined(QUADSPI_CR_DFM_Pos)
| 0 << QUADSPI_CR_DFM_Pos // dual-flash mode disabled
#endif
| 1 << QUADSPI_CR_SSHIFT_Pos // do sample shift
| 0 << QUADSPI_CR_TCEN_Pos // timeout counter disabled (see F7 errata)
| MICROPY_HW_QSPI_SAMPLE_SHIFT << QUADSPI_CR_SSHIFT_Pos
| MICROPY_HW_QSPI_TIMEOUT_COUNTER << QUADSPI_CR_TCEN_Pos
| 1 << QUADSPI_CR_EN_Pos // enable the peripheral
;
QUADSPI->DCR =
(MICROPY_HW_QSPIFLASH_SIZE_BITS_LOG2 - 3 - 1) << QUADSPI_DCR_FSIZE_Pos
| 1 << QUADSPI_DCR_CSHT_Pos // nCS stays high for 2 cycles
| (MICROPY_HW_QSPI_CS_HIGH_CYCLES - 1) << QUADSPI_DCR_CSHT_Pos
| 0 << QUADSPI_DCR_CKMODE_Pos // CLK idles at low state
;
}