menu "PHY" config ESP_PHY_CALIBRATION_AND_DATA_STORAGE bool "Store phy calibration data in NVS" default y help If this option is enabled, NVS will be initialized and calibration data will be loaded from there. PHY calibration will be skipped on deep sleep wakeup. If calibration data is not found, full calibration will be performed and stored in NVS. Normally, only partial calibration will be performed. If this option is disabled, full calibration will be performed. If it's easy that your board calibrate bad data, choose 'n'. Two cases for example, you should choose 'n': 1.If your board is easy to be booted up with antenna disconnected. 2.Because of your board design, each time when you do calibration, the result are too unstable. If unsure, choose 'y'. menuconfig ESP_PHY_INIT_DATA_IN_PARTITION bool "Use a partition to store PHY init data" depends on SOC_WIFI_SUPPORTED default n help If enabled, PHY init data will be loaded from a partition. When using a custom partition table, make sure that PHY data partition is included (type: 'data', subtype: 'phy'). With default partition tables, this is done automatically. If PHY init data is stored in a partition, it has to be flashed there, otherwise runtime error will occur. If this option is not enabled, PHY init data will be embedded into the application binary. If unsure, choose 'n'. config ESP_PHY_DEFAULT_INIT_IF_INVALID bool "Reset default PHY init data if invalid" default n depends on ESP_PHY_INIT_DATA_IN_PARTITION help If enabled, PHY init data will be restored to default if it cannot be verified successfully to avoid endless bootloops. If unsure, choose 'n'. if ESP_PHY_INIT_DATA_IN_PARTITION config ESP_PHY_MULTIPLE_INIT_DATA_BIN bool "Support multiple PHY init data bin" depends on ESP_PHY_INIT_DATA_IN_PARTITION default n help If enabled, the corresponding PHY init data type can be automatically switched according to the country code. China's PHY init data bin is used by default. Can be modified by country information in API esp_wifi_set_country(). The priority of switching the PHY init data type is: 1. Country configured by API esp_wifi_set_country() and the parameter policy is WIFI_COUNTRY_POLICY_MANUAL. 2. Country notified by the connected AP. 3. Country configured by API esp_wifi_set_country() and the parameter policy is WIFI_COUNTRY_POLICY_AUTO. config ESP_PHY_MULTIPLE_INIT_DATA_BIN_EMBED bool "Support embedded multiple phy init data bin to app bin" depends on ESP_PHY_MULTIPLE_INIT_DATA_BIN default n help If enabled, multiple phy init data bin will embedded into app bin If not enabled, multiple phy init data bin will still leave alone, and need to be flashed by users. config ESP_PHY_INIT_DATA_ERROR bool "Terminate operation when PHY init data error" depends on ESP_PHY_MULTIPLE_INIT_DATA_BIN default n help If enabled, when an error occurs while the PHY init data is updated, the program will terminate and restart. If not enabled, the PHY init data will not be updated when an error occurs. endif config ESP_PHY_MAX_WIFI_TX_POWER int "Max WiFi TX power (dBm)" range 10 20 default 20 help Set maximum transmit power for WiFi radio. Actual transmit power for high data rates may be lower than this setting. config ESP_PHY_MAX_TX_POWER int default ESP_PHY_MAX_WIFI_TX_POWER config ESP_PHY_MAC_BB_PD bool "Power down MAC and baseband of Wi-Fi and Bluetooth when PHY is disabled" depends on SOC_PM_SUPPORT_MAC_BB_PD && FREERTOS_USE_TICKLESS_IDLE default n help If enabled, the MAC and baseband of Wi-Fi and Bluetooth will be powered down when PHY is disabled. Enabling this setting reduces power consumption by a small amount but increases RAM use by approximately 4 KB(Wi-Fi only), 2 KB(Bluetooth only) or 5.3 KB(Wi-Fi + Bluetooth). config ESP_PHY_REDUCE_TX_POWER bool "Reduce PHY TX power when brownout reset" depends on ESP_BROWNOUT_DET default n help When brownout reset occurs, reduce PHY TX power to keep the code running. config ESP_PHY_ENABLE_USB bool "Keep the USB PHY enabled when initializing WiFi" depends on SOC_WIFI_PHY_NEEDS_USB_WORKAROUND default y if IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32S3 \ || ESP_CONSOLE_USB_SERIAL_JTAG || ESP_CONSOLE_SECONDARY_USB_SERIAL_JTAG default n help On some ESP targets, the USB PHY can interfere with WiFi thus lowering WiFi performance. As a result, on those affected ESP targets, the ESP PHY library's initialization will automatically disable the USB PHY to get best WiFi performance. This option controls whether or not the ESP PHY library will keep the USB PHY enabled on initialization. Note: This option can be disabled to increase WiFi performance. However, disabling this option will also mean that the USB PHY cannot be used while WiFi is enabled. config ESP_PHY_ENABLE_CERT_TEST bool "Enable RF certification test functions" default n depends on IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32S3 help If enabled, you can use RF certification test APIs. choice ESP_PHY_CALIBRATION_MODE prompt "Calibration mode" default ESP_PHY_RF_CAL_PARTIAL help Select PHY calibration mode. During RF initialization, the partial calibration method is used by default for RF calibration. Full calibration takes about 100ms more than partial calibration. If boot duration is not critical, it is suggested to use the full calibration method. No calibration method is only used when the device wakes up from deep sleep. config ESP_PHY_RF_CAL_PARTIAL bool "Calibration partial" config ESP_PHY_RF_CAL_NONE bool "Calibration none" config ESP_PHY_RF_CAL_FULL bool "Calibration full" endchoice #ESP_PHY_CALIBRATION_MODE config ESP_PHY_CALIBRATION_MODE int default 0 if ESP_PHY_RF_CAL_PARTIAL default 1 if ESP_PHY_RF_CAL_NONE default 2 if ESP_PHY_RF_CAL_FULL config ESP_PHY_IMPROVE_RX_11B bool "Improve Wi-Fi receive 11b pkts" default n depends on SOC_PHY_IMPROVE_RX_11B help This is a workaround to improve Wi-Fi receive 11b pkts for some modules using AC-DC power supply with high interference, enable this option will sacrifice Wi-Fi OFDM receive performance. But to guarantee 11b receive performance serves as a bottom line in this case. config ESP_PHY_PLL_TRACK_DEBUG bool "Enable pll track logging" default n help If enabled, there will be some logs while pll tracking endmenu # PHY