/* * SPDX-FileCopyrightText: 2022-2024 Espressif Systems (Shanghai) CO LTD * * SPDX-License-Identifier: Apache-2.0 */ // The LL layer for I2C register operations #pragma once #include #include "hal/misc.h" #include "hal/assert.h" #include "soc/i2c_periph.h" #include "soc/soc_caps.h" #include "soc/i2c_struct.h" #include "soc/pcr_struct.h" #include "hal/i2c_types.h" #include "soc/clk_tree_defs.h" #include "soc/lp_clkrst_struct.h" #include "soc/lpperi_struct.h" #include "hal/misc.h" #ifdef __cplusplus extern "C" { #endif /** * @brief I2C hardware cmd register fields. */ typedef union { struct { uint32_t byte_num: 8, /*!< Specifies the length of data (in bytes) to be read or written */ ack_en: 1, /*!< Used to enable the I2C controller during a write operation to check whether ACK */ ack_exp: 1, /*!< Used to configure the level of the ACK bit expected by the I2C controller during a write operation */ ack_val: 1, /*!< Used to configure the level of the ACK bit sent by the I2C controller during a read operation */ op_code: 3, /*!< Indicates the command */ reserved14: 17, /*!< Reserved bits */ done: 1; /*!< Indicates that a command has been executed */ }; uint32_t val; } i2c_ll_hw_cmd_t; // I2C operation mode command #define I2C_LL_CMD_RESTART 6 /*!clkm_div = clkm_div; clk_cal->scl_low = half_cycle; // default, scl_wait_high < scl_high // Make 80KHz as a boundary here, because when working at lower frequency, too much scl_wait_high will faster the frequency // according to some hardware behaviors. clk_cal->scl_wait_high = (bus_freq >= 80 * 1000) ? (half_cycle / 2 - 2) : (half_cycle / 4); clk_cal->scl_high = half_cycle - clk_cal->scl_wait_high; clk_cal->sda_hold = half_cycle / 4; clk_cal->sda_sample = half_cycle / 2; clk_cal->setup = half_cycle; clk_cal->hold = half_cycle; //default we set the timeout value to about 10 bus cycles // log(20*half_cycle)/log(2) = log(half_cycle)/log(2) + log(20)/log(2) clk_cal->tout = (int)(sizeof(half_cycle) * 8 - __builtin_clz(5 * half_cycle)) + 2; /* Verify the assumptions made by the hardware */ HAL_ASSERT(clk_cal->scl_wait_high < clk_cal->sda_sample && clk_cal->sda_sample < clk_cal->scl_high); } /** * @brief Update I2C configuration * * @param hw Beginning address of the peripheral registers * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_update(i2c_dev_t *hw) { hw->ctr.conf_upgate = 1; } /** * @brief Enable the bus clock for I2C module * * @param i2c_port I2C port id * @param enable true to enable, false to disable */ static inline void i2c_ll_enable_bus_clock(int i2c_port, bool enable) { (void)i2c_port; PCR.i2c_conf.i2c_clk_en = enable; } /** * @brief Reset the I2C module * * @param i2c_port Group ID */ static inline void i2c_ll_reset_register(int i2c_port) { (void)i2c_port; PCR.i2c_conf.i2c_rst_en = 1; PCR.i2c_conf.i2c_rst_en = 0; } /** * @brief Configure the I2C bus timing related register. * * @param hw Beginning address of the peripheral registers * @param bus_cfg Pointer to the data structure holding the register configuration. * * @return None */ static inline void i2c_ll_master_set_bus_timing(i2c_dev_t *hw, i2c_hal_clk_config_t *bus_cfg) { HAL_FORCE_MODIFY_U32_REG_FIELD(PCR.i2c_sclk_conf, i2c_sclk_div_num, bus_cfg->clkm_div - 1); /* Set div_a and div_b to 0, as it's not necessary to use them */ HAL_FORCE_MODIFY_U32_REG_FIELD(PCR.i2c_sclk_conf, i2c_sclk_div_a, 0); HAL_FORCE_MODIFY_U32_REG_FIELD(PCR.i2c_sclk_conf, i2c_sclk_div_b, 0); /* According to the Technical Reference Manual, the following timings must be subtracted by 1. * However, according to the practical measurement and some hardware behaviour, if wait_high_period and scl_high minus one. * The SCL frequency would be a little higher than expected. Therefore, the solution * here is not to minus scl_high as well as scl_wait high, and the frequency will be absolutely accurate to all frequency * to some extent. */ hw->scl_low_period.scl_low_period = bus_cfg->scl_low - 1; hw->scl_high_period.scl_high_period = bus_cfg->scl_high; hw->scl_high_period.scl_wait_high_period = bus_cfg->scl_wait_high; //sda sample hw->sda_hold.sda_hold_time = bus_cfg->sda_hold - 1; hw->sda_sample.sda_sample_time = bus_cfg->sda_sample - 1; //setup hw->scl_rstart_setup.scl_rstart_setup_time = bus_cfg->setup - 1; hw->scl_stop_setup.scl_stop_setup_time = bus_cfg->setup - 1; //hold hw->scl_start_hold.scl_start_hold_time = bus_cfg->hold - 1; hw->scl_stop_hold.scl_stop_hold_time = bus_cfg->hold - 1; hw->to.time_out_value = bus_cfg->tout; hw->to.time_out_en = 1; } /** * @brief Set fractional divider * * @param hw Beginning address of the peripheral registers * @param div_a The denominator of the frequency divider factor of the i2c function clock * @param div_b The numerator of the frequency divider factor of the i2c function clock. */ static inline void i2c_ll_master_set_fractional_divider(i2c_dev_t *hw, uint8_t div_a, uint8_t div_b) { /* Set div_a and div_b to 0, as it's not necessary to use them */ HAL_FORCE_MODIFY_U32_REG_FIELD(PCR.i2c_sclk_conf, i2c_sclk_div_a, div_a); HAL_FORCE_MODIFY_U32_REG_FIELD(PCR.i2c_sclk_conf, i2c_sclk_div_b, div_b); } /** * @brief Reset I2C txFIFO * * @param hw Beginning address of the peripheral registers * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_txfifo_rst(i2c_dev_t *hw) { hw->fifo_conf.tx_fifo_rst = 1; hw->fifo_conf.tx_fifo_rst = 0; } /** * @brief Reset I2C rxFIFO * * @param hw Beginning address of the peripheral registers * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_rxfifo_rst(i2c_dev_t *hw) { hw->fifo_conf.rx_fifo_rst = 1; hw->fifo_conf.rx_fifo_rst = 0; } /** * @brief Clear I2C interrupt status * * @param hw Beginning address of the peripheral registers * @param mask Interrupt mask needs to be cleared * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_clear_intr_mask(i2c_dev_t *hw, uint32_t mask) { hw->int_clr.val = mask; } /** * @brief Enable I2C interrupt * * @param hw Beginning address of the peripheral registers * @param mask Interrupt mask needs to be enabled * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_enable_intr_mask(i2c_dev_t *hw, uint32_t mask) { hw->int_ena.val |= mask; } /** * @brief Disable I2C interrupt * * @param hw Beginning address of the peripheral registers * @param mask Interrupt mask needs to be disabled * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_disable_intr_mask(i2c_dev_t *hw, uint32_t mask) { hw->int_ena.val &= (~mask); } /** * @brief Get I2C interrupt status * * @param hw Beginning address of the peripheral registers * * @return I2C interrupt status */ __attribute__((always_inline)) static inline void i2c_ll_get_intr_mask(i2c_dev_t *hw, uint32_t *intr_status) { *intr_status = hw->int_status.val; } /** * @brief Configure I2C memory access mode, FIFO mode or non-FIFO mode * * @param hw Beginning address of the peripheral registers * @param fifo_mode_en Set true to enable FIFO access mode, else, set it false * * @return None */ static inline void i2c_ll_slave_set_fifo_mode(i2c_dev_t *hw, bool fifo_mode_en) { hw->fifo_conf.nonfifo_en = fifo_mode_en ? 0 : 1; } /** * @brief Configure I2C timeout * * @param hw Beginning address of the peripheral registers * @param tout_num The I2C timeout value needs to be set (2^tout in core clock cycle) * * @return None */ static inline void i2c_ll_set_tout(i2c_dev_t *hw, int tout) { hw->to.time_out_value = tout; } /** * @brief Configure I2C slave broadcasting mode. * * @param hw Beginning address of the peripheral registers * @param broadcast_en Set true to enable broadcast, else, set it false * * @return None */ static inline void i2c_ll_slave_broadcast_enable(i2c_dev_t *hw, bool broadcast_en) { hw->ctr.addr_broadcasting_en = broadcast_en; } /** * @brief Get the cause of SCL clock stretching in slave mode * * @param hw Beginning address of the peripheral registers * @param stretch_cause Pointer to stretch cause in the slave mode. * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_slave_get_stretch_cause(i2c_dev_t *hw, i2c_slave_stretch_cause_t *stretch_cause) { switch (hw->sr.stretch_cause) { case 0: *stretch_cause = I2C_SLAVE_STRETCH_CAUSE_ADDRESS_MATCH; break; case 1: *stretch_cause = I2C_SLAVE_STRETCH_CAUSE_TX_EMPTY; break; case 2: *stretch_cause = I2C_SLAVE_STRETCH_CAUSE_RX_FULL; break; case 3: *stretch_cause = I2C_SLAVE_STRETCH_CAUSE_SENDING_ACK; break; default: HAL_ASSERT(false); break; } } /** * @brief Configure I2C slave address * * @param hw Beginning address of the peripheral registers * @param slave_addr I2C slave address needs to be set * @param addr_10bit_en Set true to enable 10-bit slave address mode, set false to enable 7-bit address mode * * @return None */ static inline void i2c_ll_set_slave_addr(i2c_dev_t *hw, uint16_t slave_addr, bool addr_10bit_en) { hw->slave_addr.addr_10bit_en = addr_10bit_en; if (addr_10bit_en) { uint16_t addr_14_7 = (slave_addr & 0xff) << 7; uint8_t addr_6_0 = ((slave_addr & 0x300) >> 8) | 0x78; hw->slave_addr.slave_addr = addr_14_7 | addr_6_0; hw->ctr.addr_10bit_rw_check_en = addr_10bit_en; } else { hw->slave_addr.slave_addr = slave_addr; } } /** * @brief Write I2C hardware command register * * @param hw Beginning address of the peripheral registers * @param cmd I2C hardware command * @param cmd_idx The index of the command register, should be less than 16 * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_master_write_cmd_reg(i2c_dev_t *hw, i2c_ll_hw_cmd_t cmd, int cmd_idx) { hw->command[cmd_idx].val = cmd.val; } /** * @brief Configure I2C start timing * * @param hw Beginning address of the peripheral registers * @param start_setup The start condition setup period (in core clock cycle) * @param start_hold The start condition hold period (in core clock cycle) * * @return None */ static inline void i2c_ll_master_set_start_timing(i2c_dev_t *hw, int start_setup, int start_hold) { hw->scl_rstart_setup.scl_rstart_setup_time = start_setup; hw->scl_start_hold.scl_start_hold_time = start_hold - 1; } /** * @brief Configure I2C stop timing * * @param hw Beginning address of the peripheral registers * @param stop_setup The stop condition setup period (in core clock cycle) * @param stop_hold The stop condition hold period (in core clock cycle) * * @return None */ static inline void i2c_ll_master_set_stop_timing(i2c_dev_t *hw, int stop_setup, int stop_hold) { hw->scl_stop_setup.scl_stop_setup_time = stop_setup; hw->scl_stop_hold.scl_stop_hold_time = stop_hold; } /** * @brief Configure I2C stop timing * * @param hw Beginning address of the peripheral registers * @param sda_sample The SDA sample time (in core clock cycle) * @param sda_hold The SDA hold time (in core clock cycle) * * @return None */ static inline void i2c_ll_set_sda_timing(i2c_dev_t *hw, int sda_sample, int sda_hold) { hw->sda_hold.sda_hold_time = sda_hold; hw->sda_sample.sda_sample_time = sda_sample; } /** * @brief Set I2C txFIFO empty threshold * * @param hw Beginning address of the peripheral registers * @param empty_thr The txFIFO empty threshold * * @return None */ static inline void i2c_ll_set_txfifo_empty_thr(i2c_dev_t *hw, uint8_t empty_thr) { hw->fifo_conf.txfifo_wm_thrhd = empty_thr; } /** * @brief Set I2C rxFIFO full threshold * * @param hw Beginning address of the peripheral registers * @param full_thr The rxFIFO full threshold * * @return None */ static inline void i2c_ll_set_rxfifo_full_thr(i2c_dev_t *hw, uint8_t full_thr) { hw->fifo_conf.fifo_prt_en = 1; hw->fifo_conf.rxfifo_wm_thrhd = full_thr; } /** * @brief Set the I2C data mode, LSB or MSB * * @param hw Beginning address of the peripheral registers * @param tx_mode Tx data bit mode * @param rx_mode Rx data bit mode * * @return None */ static inline void i2c_ll_set_data_mode(i2c_dev_t *hw, i2c_trans_mode_t tx_mode, i2c_trans_mode_t rx_mode) { hw->ctr.tx_lsb_first = tx_mode; hw->ctr.rx_lsb_first = rx_mode; } /** * @brief Get I2C sda timing configuration * * @param hw Beginning address of the peripheral registers * @param sda_sample Pointer to accept the SDA sample timing configuration * @param sda_hold Pointer to accept the SDA hold timing configuration * * @return None */ static inline void i2c_ll_get_sda_timing(i2c_dev_t *hw, int *sda_sample, int *sda_hold) { *sda_hold = hw->sda_hold.sda_hold_time; *sda_sample = hw->sda_sample.sda_sample_time; } /** * @brief Get the I2C hardware version * * @param hw Beginning address of the peripheral registers * * @return The I2C hardware version */ static inline uint32_t i2c_ll_get_hw_version(i2c_dev_t *hw) { return hw->date.date; } /** * @brief Check if the I2C bus is busy * * @param hw Beginning address of the peripheral registers * * @return True if I2C state machine is busy, else false will be returned */ __attribute__((always_inline)) static inline bool i2c_ll_is_bus_busy(i2c_dev_t *hw) { return hw->sr.bus_busy; } /** * @brief Check if I2C is master mode * * @param hw Beginning address of the peripheral registers * * @return True if I2C is master mode, else false will be returned */ static inline bool i2c_ll_is_master_mode(i2c_dev_t *hw) { return hw->ctr.ms_mode; } /** * @brief Get the rxFIFO readable length * * @param hw Beginning address of the peripheral registers * * @return RxFIFO readable length */ __attribute__((always_inline)) static inline void i2c_ll_get_rxfifo_cnt(i2c_dev_t *hw, uint32_t *length) { *length = hw->sr.rxfifo_cnt; } /** * @brief Get I2C txFIFO writable length * * @param hw Beginning address of the peripheral registers * * @return TxFIFO writable length */ __attribute__((always_inline)) static inline void i2c_ll_get_txfifo_len(i2c_dev_t *hw, uint32_t *length) { *length = SOC_I2C_FIFO_LEN - hw->sr.txfifo_cnt; } /** * @brief Get I2C timeout configuration * * @param hw Beginning address of the peripheral registers * * @return The I2C timeout value */ static inline void i2c_ll_get_tout(i2c_dev_t *hw, int *timeout) { *timeout = hw->to.time_out_value; } /** * @brief Start I2C transfer * * @param hw Beginning address of the peripheral registers * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_master_trans_start(i2c_dev_t *hw) { hw->ctr.trans_start = 1; } /** * @brief Get I2C start timing configuration * * @param hw Beginning address of the peripheral registers * @param setup_time Pointer to accept the start condition setup period * @param hold_time Pointer to accept the start condition hold period * * @return None */ static inline void i2c_ll_get_start_timing(i2c_dev_t *hw, int *setup_time, int *hold_time) { *setup_time = hw->scl_rstart_setup.scl_rstart_setup_time; *hold_time = hw->scl_start_hold.scl_start_hold_time + 1; } /** * @brief Get I2C stop timing configuration * * @param hw Beginning address of the peripheral registers * @param setup_time Pointer to accept the stop condition setup period * @param hold_time Pointer to accept the stop condition hold period * * @return None */ static inline void i2c_ll_get_stop_timing(i2c_dev_t *hw, int *setup_time, int *hold_time) { *setup_time = hw->scl_stop_setup.scl_stop_setup_time; *hold_time = hw->scl_stop_hold.scl_stop_hold_time; } /** * @brief Write the I2C hardware txFIFO * * @param hw Beginning address of the peripheral registers * @param ptr Pointer to data buffer * @param len Amount of data needs to be writen * * @return None. */ __attribute__((always_inline)) static inline void i2c_ll_write_txfifo(i2c_dev_t *hw, const uint8_t *ptr, uint8_t len) { for (int i = 0; i < len; i++) { HAL_FORCE_MODIFY_U32_REG_FIELD(hw->data, fifo_rdata, ptr[i]); } } /** * @brief Read the I2C hardware rxFIFO * * @param hw Beginning address of the peripheral registers * @param ptr Pointer to data buffer * @param len Amount of data needs read * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_read_rxfifo(i2c_dev_t *hw, uint8_t *ptr, uint8_t len) { for (int i = 0; i < len; i++) { ptr[i] = HAL_FORCE_READ_U32_REG_FIELD(hw->data, fifo_rdata); } } /** * @brief Write the I2C hardware txFIFO * * @param hw Beginning address of the peripheral registers * @param ram_offset Offset value of I2C RAM. * @param ptr Pointer to data buffer * @param len Amount of data needs to be writen */ static inline void i2c_ll_write_by_nonfifo(i2c_dev_t *hw, uint8_t ram_offset, const uint8_t *ptr, uint8_t len) { for (int i = 0; i < len; i++) { hw->txfifo_mem[i + ram_offset] = ptr[i]; } } /** * @brief Read the I2C hardware ram * * @param hw Beginning address of the peripheral registers * @param ram_offset Offset value of I2C RAM. * @param ptr Pointer to data buffer * @param len Amount of data needs read */ static inline void i2c_ll_read_by_nonfifo(i2c_dev_t *hw, uint8_t ram_offset, uint8_t *ptr, uint8_t len) { for (int i = 0; i < len; i++) { ptr[i] = hw->rxfifo_mem[i + ram_offset]; } } /** * @brief Get access to I2C RAM address directly * * @param hw Beginning address of the peripheral registers * @param addr_wr_en Enable I2C ram address read and write * * @return None */ static inline void i2c_ll_enable_mem_access_nonfifo(i2c_dev_t *hw, bool addr_wr_en) { hw->fifo_conf.fifo_addr_cfg_en = addr_wr_en; } /** * @brief Configure I2C hardware filter * * @param hw Beginning address of the peripheral registers * @param filter_num If the glitch period on the line is less than this value, it can be filtered out * If `filter_num == 0`, the filter will be disabled * * @return None */ static inline void i2c_ll_master_set_filter(i2c_dev_t *hw, uint8_t filter_num) { if (filter_num > 0) { hw->filter_cfg.scl_filter_thres = filter_num; hw->filter_cfg.sda_filter_thres = filter_num; hw->filter_cfg.scl_filter_en = 1; hw->filter_cfg.sda_filter_en = 1; } else { hw->filter_cfg.scl_filter_en = 0; hw->filter_cfg.sda_filter_en = 0; } } /** * @brief Get I2C hardware filter configuration * * @param hw Beginning address of the peripheral registers * * @return The hardware filter configuration */ static inline void i2c_ll_master_get_filter(i2c_dev_t *hw, uint8_t *filter_conf) { *filter_conf = hw->filter_cfg.scl_filter_thres; } /** * @brief Reste I2C master FSM. When the master FSM is stuck, call this function to reset the FSM * * @param hw Beginning address of the peripheral registers * * @return None */ static inline void i2c_ll_master_fsm_rst(i2c_dev_t *hw) { // fsm_rst is a self cleared bit. hw->ctr.fsm_rst = 1; } /** * @brief Clear I2C bus, when the slave is stuck in a deadlock and keeps pulling the bus low, * master can controls the SCL bus to generate 9 CLKs. * * Note: The master cannot detect if deadlock happens, but when the scl_st_to interrupt is generated, a deadlock may occur. * * @param hw Beginning address of the peripheral registers * @param slave_pulses When I2C master is IDLE, the number of pulses will be sent out. * * @return None */ static inline void i2c_ll_master_clr_bus(i2c_dev_t *hw, uint32_t slave_pulses) { hw->scl_sp_conf.scl_rst_slv_num = slave_pulses; hw->scl_sp_conf.scl_rst_slv_en = 1; hw->ctr.conf_upgate = 1; // hardward will clear scl_rst_slv_en after sending SCL pulses, // and we should set conf_upgate bit to synchronize register value. while (hw->scl_sp_conf.scl_rst_slv_en); hw->ctr.conf_upgate = 1; } /** * @brief Set the ACK level that the I2C master must send when the Rx FIFO count has reached the threshold value. * ack_level: 1 (NACK) * ack_level: 0 (ACK) * * @param hw Beginning address of the peripheral registers * * @return None */ static inline void i2c_ll_master_rx_full_ack_level(i2c_dev_t *hw, int ack_level) { hw->ctr.rx_full_ack_level = ack_level; } /** * @brief Set I2C source clock * * @param hw Beginning address of the peripheral registers * @param src_clk Source clock of the I2C * * @return None */ static inline void i2c_ll_set_source_clk(i2c_dev_t *hw, i2c_clock_source_t src_clk) { if (hw == &LP_I2C) { // Do nothing return; } // src_clk : (1) for RTC_CLK, (0) for XTAL PCR.i2c_sclk_conf.i2c_sclk_sel = (src_clk == I2C_CLK_SRC_RC_FAST) ? 1 : 0; } /** * @brief Set LP I2C source clock * * @param hw Address offset of the LP I2C peripheral registers * @param src_clk Source clock for the LP I2C peripheral */ static inline void lp_i2c_ll_set_source_clk(i2c_dev_t *hw, soc_periph_lp_i2c_clk_src_t src_clk) { (void)hw; // src_clk : (0) for LP_FAST_CLK (RTC Fast), (1) for XTAL_D2_CLK switch (src_clk) { case LP_I2C_SCLK_LP_FAST: LP_CLKRST.lpperi.lp_i2c_clk_sel = 0; break; case LP_I2C_SCLK_XTAL_D2: LP_CLKRST.lpperi.lp_i2c_clk_sel = 1; break; default: // Invalid source clock selected HAL_ASSERT(false); } } /// LP_CLKRST.lpperi is a shared register, so this function must be used in an atomic way #define lp_i2c_ll_set_source_clk(...) (void)__DECLARE_RCC_ATOMIC_ENV; lp_i2c_ll_set_source_clk(__VA_ARGS__) /** * @brief Enable bus clock for the LP I2C module * * @param hw_id LP I2C instance ID * @param enable True to enable, False to disable */ static inline void _lp_i2c_ll_enable_bus_clock(int hw_id, bool enable) { (void)hw_id; LPPERI.clk_en.lp_ext_i2c_ck_en = enable; } /// LPPERI.clk_en is a shared register, so this function must be used in an atomic way #define lp_i2c_ll_enable_bus_clock(...) (void)__DECLARE_RCC_ATOMIC_ENV; _lp_i2c_ll_enable_bus_clock(__VA_ARGS__) /** * @brief Reset LP I2C module * * @param hw_id LP I2C instance ID */ static inline void lp_i2c_ll_reset_register(int hw_id) { (void)hw_id; LPPERI.reset_en.lp_ext_i2c_reset_en = 1; LPPERI.reset_en.lp_ext_i2c_reset_en = 0; } /// LPPERI.reset_en is a shared register, so this function must be used in an atomic way #define lp_i2c_ll_reset_register(...) (void)__DECLARE_RCC_ATOMIC_ENV; lp_i2c_ll_reset_register(__VA_ARGS__) /** * @brief Enable I2C peripheral controller clock * * @param dev Peripheral instance address * @param en True to enable, False to disable */ static inline void i2c_ll_enable_controller_clock(i2c_dev_t *hw, bool en) { if (hw == &LP_I2C) { // Do nothing return; } PCR.i2c_sclk_conf.i2c_sclk_en = en; } /** * @brief Init I2C master * * @param hw Beginning address of the peripheral registers * * @return None */ static inline void i2c_ll_master_init(i2c_dev_t *hw) { typeof(hw->ctr) ctrl_reg; ctrl_reg.val = 0; ctrl_reg.ms_mode = 1; ctrl_reg.sda_force_out = 1; ctrl_reg.scl_force_out = 1; hw->ctr.val = ctrl_reg.val; } /** * @brief Init I2C slave * * @param hw Beginning address of the peripheral registers * * @return None */ static inline void i2c_ll_slave_init(i2c_dev_t *hw) { typeof(hw->ctr) ctrl_reg; ctrl_reg.val = 0; ctrl_reg.sda_force_out = 1; ctrl_reg.scl_force_out = 1; hw->ctr.val = ctrl_reg.val; hw->fifo_conf.fifo_addr_cfg_en = 0; } /** * @brief Set whether slave should auto start, or only start with start signal from master * * @param hw Beginning address of the peripheral registers * @param slv_ex_auto_en 1 if slave auto start data transaction, otherwise, 0. */ static inline void i2c_ll_slave_tx_auto_start_en(i2c_dev_t *hw, bool slv_ex_auto_en) { hw->ctr.slv_tx_auto_start_en = slv_ex_auto_en; } /** * @brief Get I2C interrupt status register address */ static inline volatile void *i2c_ll_get_interrupt_status_reg(i2c_dev_t *dev) { return &dev->int_status; } /** * @brief Enable I2C slave clock stretch. * * @param dev Beginning address of the peripheral registers. * @param enable true: Enable, false: Disable. */ static inline void i2c_ll_slave_enable_scl_stretch(i2c_dev_t *dev, bool enable) { dev->scl_stretch_conf.slave_scl_stretch_en = enable; } /** * @brief Clear I2C clock stretch status * * @param dev Beginning address of the peripheral registers */ __attribute__((always_inline)) static inline void i2c_ll_slave_clear_stretch(i2c_dev_t *dev) { dev->scl_stretch_conf.slave_scl_stretch_clr = 1; } /** * @brief Check if i2c command is done. * * @param hw Beginning address of the peripheral registers * @param cmd_idx The index of the command register, must be less than 8 * * @return True if the `cmd_idx` command is done. Otherwise false. */ __attribute__((always_inline)) static inline bool i2c_ll_master_is_cmd_done(i2c_dev_t *hw, int cmd_idx) { return hw->command[cmd_idx].command_done; } //////////////////////////////////////////Deprecated Functions////////////////////////////////////////////////////////// /////////////////////////////The following functions are only used by the legacy driver///////////////////////////////// /////////////////////////////They might be removed in the next major release (ESP-IDF 6.0)////////////////////////////// //////////////////////////////////////////////////////////////////////////////////////////////////////////////////////// // I2C master TX interrupt bitmap #define I2C_LL_MASTER_TX_INT (I2C_NACK_INT_ENA_M|I2C_TIME_OUT_INT_ENA_M|I2C_TRANS_COMPLETE_INT_ENA_M|I2C_ARBITRATION_LOST_INT_ENA_M|I2C_END_DETECT_INT_ENA_M) // I2C master RX interrupt bitmap #define I2C_LL_MASTER_RX_INT (I2C_TIME_OUT_INT_ENA_M|I2C_TRANS_COMPLETE_INT_ENA_M|I2C_ARBITRATION_LOST_INT_ENA_M|I2C_END_DETECT_INT_ENA_M) // I2C slave TX interrupt bitmap #define I2C_LL_SLAVE_TX_INT (I2C_TXFIFO_WM_INT_ENA_M) // I2C slave RX interrupt bitmap #define I2C_LL_SLAVE_RX_INT (I2C_RXFIFO_WM_INT_ENA_M | I2C_TRANS_COMPLETE_INT_ENA_M) // I2C max timeout value #define I2C_LL_MAX_TIMEOUT I2C_TIME_OUT_VALUE #define I2C_LL_INTR_MASK (0x3fff) /*!< I2C all interrupt bitmap */ /** * @brief I2C interrupt event */ typedef enum { I2C_INTR_EVENT_ERR, I2C_INTR_EVENT_ARBIT_LOST, /*!< I2C arbition lost event */ I2C_INTR_EVENT_NACK, /*!< I2C NACK event */ I2C_INTR_EVENT_TOUT, /*!< I2C time out event */ I2C_INTR_EVENT_END_DET, /*!< I2C end detected event */ I2C_INTR_EVENT_TRANS_DONE, /*!< I2C trans done event */ I2C_INTR_EVENT_RXFIFO_FULL, /*!< I2C rxfifo full event */ I2C_INTR_EVENT_TXFIFO_EMPTY, /*!< I2C txfifo empty event */ } i2c_intr_event_t; /** * @brief Configure I2C SCL timing * * @param hw Beginning address of the peripheral registers * @param high_period The I2C SCL hight period (in core clock cycle, hight_period > 2) * @param low_period The I2C SCL low period (in core clock cycle, low_period > 1) * @param wait_high_period The I2C SCL wait rising edge period. * * @return None. */ static inline void i2c_ll_set_scl_clk_timing(i2c_dev_t *hw, int high_period, int low_period, int wait_high_period) { hw->scl_low_period.scl_low_period = low_period; hw->scl_high_period.scl_high_period = high_period; hw->scl_high_period.scl_wait_high_period = wait_high_period; } /** * @brief Get I2C SCL timing configuration * * @param hw Beginning address of the peripheral registers * @param high_period Pointer to accept the SCL high period * @param low_period Pointer to accept the SCL low period * * @return None */ static inline void i2c_ll_get_scl_clk_timing(i2c_dev_t *hw, int *high_period, int *low_period, int *wait_high_period) { *high_period = hw->scl_high_period.scl_high_period; *wait_high_period = hw->scl_high_period.scl_wait_high_period; *low_period = hw->scl_low_period.scl_low_period; } /** * @brief Get I2C master interrupt event * * @param hw Beginning address of the peripheral registers * @param event Pointer to accept the interrupt event * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_master_get_event(i2c_dev_t *hw, i2c_intr_event_t *event) { i2c_int_status_reg_t int_sts; int_sts.val = hw->int_status.val; if (int_sts.arbitration_lost_int_st) { *event = I2C_INTR_EVENT_ARBIT_LOST; } else if (int_sts.nack_int_st) { *event = I2C_INTR_EVENT_NACK; } else if (int_sts.time_out_int_st) { *event = I2C_INTR_EVENT_TOUT; } else if (int_sts.end_detect_int_st) { *event = I2C_INTR_EVENT_END_DET; } else if (int_sts.trans_complete_int_st) { *event = I2C_INTR_EVENT_TRANS_DONE; } else { *event = I2C_INTR_EVENT_ERR; } } /** * @brief Get I2C slave interrupt event * * @param hw Beginning address of the peripheral registers * @param event Pointer to accept the interrupt event * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_slave_get_event(i2c_dev_t *hw, i2c_intr_event_t *event) { typeof(hw->int_status) int_sts; int_sts.val = hw->int_status.val; if (int_sts.txfifo_wm_int_st) { *event = I2C_INTR_EVENT_TXFIFO_EMPTY; } else if (int_sts.trans_complete_int_st) { *event = I2C_INTR_EVENT_TRANS_DONE; } else if (int_sts.rxfifo_wm_int_st) { *event = I2C_INTR_EVENT_RXFIFO_FULL; } else { *event = I2C_INTR_EVENT_ERR; } } /** * @brief Enable I2C master TX interrupt * * @param hw Beginning address of the peripheral registers * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_master_enable_tx_it(i2c_dev_t *hw) { hw->int_clr.val = UINT32_MAX; hw->int_ena.val = I2C_LL_MASTER_TX_INT; } /** * @brief Enable I2C master RX interrupt * * @param hw Beginning address of the peripheral registers * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_master_enable_rx_it(i2c_dev_t *hw) { hw->int_clr.val = UINT32_MAX; hw->int_ena.val = I2C_LL_MASTER_RX_INT; } /** * @brief Disable I2C master TX interrupt * * @param hw Beginning address of the peripheral registers * * @return None */ static inline void i2c_ll_master_disable_tx_it(i2c_dev_t *hw) { hw->int_ena.val &= (~I2C_LL_MASTER_TX_INT); } /** * @brief Disable I2C master RX interrupt * * @param hw Beginning address of the peripheral registers * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_master_disable_rx_it(i2c_dev_t *hw) { hw->int_ena.val &= (~I2C_LL_MASTER_RX_INT); } /** * @brief * * @param hw Beginning address of the peripheral registers * * @return None */ static inline void i2c_ll_slave_enable_tx_it(i2c_dev_t *hw) { hw->int_ena.val |= I2C_LL_SLAVE_TX_INT; } /** * @brief Enable I2C slave RX interrupt * * @param hw Beginning address of the peripheral registers * * @return None */ static inline void i2c_ll_slave_enable_rx_it(i2c_dev_t *hw) { hw->int_ena.val |= I2C_LL_SLAVE_RX_INT; } /** * @brief Disable I2C slave TX interrupt * * @param hw Beginning address of the peripheral registers * * @return None */ __attribute__((always_inline)) static inline void i2c_ll_slave_disable_tx_it(i2c_dev_t *hw) { hw->int_ena.val &= (~I2C_LL_SLAVE_TX_INT); } /** * @brief Disable I2C slave RX interrupt * * @param hw Beginning address of the peripheral registers * * @return None */ static inline void i2c_ll_slave_disable_rx_it(i2c_dev_t *hw) { hw->int_ena.val &= (~I2C_LL_SLAVE_RX_INT); } /** * @brief Configure I2C SCL timing * * @param hw Beginning address of the peripheral registers * @param hight_period The I2C SCL hight period (in core clock cycle, hight_period > 2) * @param low_period The I2C SCL low period (in core clock cycle, low_period > 1) * * @return None. */ static inline void i2c_ll_set_scl_timing(i2c_dev_t *hw, int hight_period, int low_period) { hw->scl_low_period.scl_low_period = low_period - 1; hw->scl_high_period.scl_high_period = hight_period - 10; hw->scl_high_period.scl_wait_high_period = hight_period - hw->scl_high_period.scl_high_period; } /** * @brief Get the I2C data mode * * @param hw Beginning address of the peripheral registers * @param tx_mode Pointer to accept the received bytes mode * @param rx_mode Pointer to accept the sended bytes mode * * @return None */ static inline void i2c_ll_get_data_mode(i2c_dev_t *hw, i2c_trans_mode_t *tx_mode, i2c_trans_mode_t *rx_mode) { *tx_mode = (i2c_trans_mode_t)(hw->ctr.tx_lsb_first); *rx_mode = (i2c_trans_mode_t)(hw->ctr.rx_lsb_first); } /** * @brief Get I2C SCL timing configuration * * @param hw Beginning address of the peripheral registers * @param high_period Pointer to accept the SCL high period * @param low_period Pointer to accept the SCL low period * * @return None */ static inline void i2c_ll_get_scl_timing(i2c_dev_t *hw, int *high_period, int *low_period) { *high_period = hw->scl_high_period.scl_high_period + hw->scl_high_period.scl_wait_high_period; *low_period = hw->scl_low_period.scl_low_period + 1; } #ifdef __cplusplus } #endif