kopia lustrzana https://github.com/dvarrel/XCTRACK_vario
131 wiersze
3.6 KiB
C++
131 wiersze
3.6 KiB
C++
/*
|
|
VARIO XCTRACK
|
|
arduino nano
|
|
sensor ms5611
|
|
|
|
Based on Arduino Vario by Benjamin PERRIN 2017 / Vari'Up
|
|
Based on Arduino Vario by Jaros, 2012 and vario DFelix 2013
|
|
|
|
https://github.com/LK8000/LK8000/blob/master/Docs/LK8EX1.txt
|
|
$LK8EX1,pressure,altitude,vario,temperature,battery,*checksum
|
|
|
|
test sentence PRS, shorter but no checksum
|
|
*/
|
|
|
|
//MS5XXX library by Roman Schmitz
|
|
#include <MS5611.h>
|
|
#include <avr/wdt.h>
|
|
#include <SoftwareSerial.h>
|
|
|
|
/////////////////////////////////////////
|
|
MS5611 sensor(&Wire);
|
|
#define RX 11 // not used (TX module bluetooth)
|
|
#define TX 12 // MISO on ISCP (RX module bluetooth)
|
|
SoftwareSerial BTserial(RX, TX); // RX not connected
|
|
#define USB_SPEED 115200 //serial transmision speed
|
|
#define BLUETOOTH_SPEED 9600 //bluetooth speed (9600 by default)
|
|
#define FREQUENCY 10 // freq output in Hz
|
|
#define USB_MODE // usb by default
|
|
// #define BLUETOOTH_MODE // uncomment this line for bluetooth mode
|
|
#define USE_LK8000 //comment this line to use PRS sentence
|
|
// normally you do not need USB_MODE if you use BLUETOOTH_MODE
|
|
/*
|
|
these 2 sentences are available for xctrack :
|
|
LK8000 sentence : 32 chars to send
|
|
$LK8EX1,pressure,altitude,vario,temperature,battery,*checksum
|
|
|
|
PRS sentence : 10 chars to send
|
|
PRS pressure in pascal in hexadecimal format
|
|
|
|
bluetooth in 9600 bauds -> 1.25ms for a char
|
|
LK8000 : 1.25*32=40ms
|
|
PRS : 1.25*10=12.5ms
|
|
USB in 115200 bauds -> 0.08ms for a char
|
|
LK8000 : 0.08*32=2.5ms
|
|
PRS : 0.08*10=0.8ms
|
|
|
|
PRS is faster but LK8000 has checksum !
|
|
*/
|
|
|
|
const char compile_date[] = "XCTRACK VARIO " __DATE__;
|
|
const char mess_check[] = "checking MS5611 sensor...";
|
|
const char mess_error[] = "Error connecting MS5611...";
|
|
const char mess_reset[] = "Reset in 1s...";
|
|
|
|
void setup() {
|
|
wdt_disable();
|
|
delay(10);
|
|
#ifdef USB_MODE
|
|
Serial.begin(USB_SPEED);
|
|
Serial.println(compile_date);
|
|
Serial.println(mess_check);
|
|
#endif
|
|
#ifdef BLUETOOTH_MODE
|
|
BTserial.begin(BLUETOOTH_SPEED); // start communication with the HC-05 using 38400
|
|
BTserial.println(compile_date);
|
|
BTserial.println(mess_check);
|
|
#endif
|
|
wdt_enable(WDTO_1S); //enable the watchdog 1s without reset
|
|
if (sensor.connect()>0) {
|
|
#ifdef USB_MODE
|
|
Serial.println(mess_error);
|
|
Serial.println(mess_reset);
|
|
#endif
|
|
#ifdef BLUETOOTH_MODE
|
|
BTserial.println(mess_error);
|
|
BTserial.println(mess_reset);
|
|
#endif
|
|
delay(1200); //for watchdog timeout
|
|
}
|
|
sensor.ReadProm(); //takes about 3ms
|
|
}
|
|
|
|
uint32_t get_time = millis();
|
|
uint32_t sum = 0;
|
|
uint8_t n = 0;
|
|
|
|
void loop(void) {
|
|
wdt_reset();
|
|
sensor.Readout(); // with OSR4096 takes about 10ms
|
|
uint32_t Pressure = sensor.GetPres();
|
|
sum += Pressure;
|
|
//Serial.print(Pressure);
|
|
//Serial.print(",");
|
|
n += 1;
|
|
if (millis() >= (get_time + (1000/FREQUENCY))) //every 100 milli-seconds send NMEA output over serial port
|
|
{
|
|
get_time = millis();
|
|
Pressure = sum / n ;
|
|
sum=0; n=0;
|
|
uint8_t Temp = sensor.GetTemp()/100;
|
|
|
|
//$LK8EX1,pressure,altitude,vario,temperature,battery,*checksum
|
|
//$LK8EX1,pressure,99999,9999,temp,999,*checksum
|
|
|
|
#ifdef USE_LK8000
|
|
String str_out = String("LK8EX1,")
|
|
+String(Pressure)+String(",0,9999,")
|
|
+String(Temp)+String(",999,");
|
|
|
|
// Calculating checksum for data string
|
|
uint16_t checksum = 0, bi;
|
|
for (uint8_t ai = 0; ai < str_out.length(); ai++)
|
|
{
|
|
bi = (uint8_t)str_out[ai];
|
|
checksum ^= bi;
|
|
}
|
|
str_out = "$"+str_out+"*"+String(checksum, HEX);
|
|
|
|
#else // use PRS sentence
|
|
String str_out = String("PRS ")+ String(Pressure, HEX);
|
|
#endif
|
|
|
|
#ifdef USB_MODE
|
|
Serial.println(str_out);
|
|
#endif
|
|
#ifdef BLUETOOTH_MODE
|
|
BTserial.println(str_out);
|
|
#endif
|
|
}
|
|
}
|