Update README

README.MD

@@ -1,16 +1,21 @@
 # TTGO T-Display
 
 ![image](https://github.com/Xinyuan-LilyGO/TTGO-T-Display/blob/master/image/pinmap.jpg)
-
 ## 1.Install the following dependency library files:
 - [TFT_eSPI](https://github.com/Bodmer/TFT_eSPI)        
 - [Button2](https://github.com/LennartHennigs/Button2)
 
-
 ## 2.TFT_eSPI settings
-- Move or copy `User_Setups/TTGO_T_Display.h` to `TFT_eSPI/User_Setups/`
-- Add `#include <User_Setups/TTGO_T_Display.h>` to  `TFT_eSPI/User_Setup_Select.h`
-  
+- Install TFT_eSPI, in `TFT_eSPI/User_Setup_Select.h`, comment out the default settings `#include <User_Setup.h>` , select `#include <User_Setups/Setup25_TTGO_T_Display.h>` , Save Settings.
+
+* Like the picture below
+
+![2.png](image/2.png)
+
+
+## 3.Board choose
+- The board can choose `ESP32 Dev Module`, other settings can keep the default
+
 
 ## Pinout
 | Name       | V18    |
@@ -31,4 +36,4 @@
 | ADC Power  | 14     |
 
 2019/08/06:
-* The TFT_eSPI and Button2 libraries have been synchronized to the main branch
+* The TFT_eSPI and Button2 libraries have been synchronized to the main branch

TTGO_T_Display.h

@@ -1,58 +0,0 @@
-// ST7789 135 x 240 display with no chip select line
-
-#define ST7789_DRIVER     // Configure all registers
-
-#define TFT_WIDTH  135
-#define TFT_HEIGHT 240
-
-#define CGRAM_OFFSET      // Library will add offsets required
-
-// #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
-//#define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
-
-//#define TFT_INVERSION_ON
-//#define TFT_INVERSION_OFF
-
-// DSTIKE stepup
-//#define TFT_DC    23
-//#define TFT_RST   32
-//#define TFT_MOSI  26
-//#define TFT_SCLK  27
-
-// Generic ESP32 setup
-#define TFT_MISO -1
-#define TFT_MOSI 19
-#define TFT_SCLK 18
-#define TFT_CS    5 // Not connected
-#define TFT_DC    16
-#define TFT_RST   23  // Connect reset to ensure display initialises
-#define TFT_BL 4
-#define TFT_BACKLIGHT_ON HIGH
-
-// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
-// #define TFT_CS   -1      // Define as not used
-// #define TFT_DC   PIN_D1  // Data Command control pin
-//#define TFT_RST  PIN_D4  // TFT reset pin (could connect to NodeMCU RST, see next line)
-// #define TFT_RST  -1      // TFT reset pin connect to NodeMCU RST, must also then add 10K pull down to TFT SCK
-
-
-#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
-#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
-#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
-#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
-#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:.
-#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
-//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
-#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
-
-#define SMOOTH_FONT
-
-
-// #define SPI_FREQUENCY  27000000
-#define SPI_FREQUENCY  40000000
-
-#define SPI_READ_FREQUENCY  20000000
-
-#define SPI_TOUCH_FREQUENCY  2500000
-
-// #define SUPPORT_TRANSACTIONS