From 913ee90936ff31b7e4db90ba6bdb17d6fa5d84ca Mon Sep 17 00:00:00 2001 From: Mateusz Lubecki Date: Tue, 31 Aug 2021 17:57:18 +0200 Subject: [PATCH] example config for parameteo --- include/station_config_example_parameteo.h | 286 +++++++++++++++++++++ 1 file changed, 286 insertions(+) create mode 100644 include/station_config_example_parameteo.h diff --git a/include/station_config_example_parameteo.h b/include/station_config_example_parameteo.h new file mode 100644 index 0000000..c6c40bd --- /dev/null +++ b/include/station_config_example_parameteo.h @@ -0,0 +1,286 @@ +/* + * config.h + * + * Created on: 03.07.2017 + * Author: mateusz + */ + +#ifndef STATION_CONFIG_H_ +#define STATION_CONFIG_H_ + +/* ------------------ */ +/* MODES OF OPERATION */ + +#define _METEO // Enable meteo station +#define _DIGI // Enable WIDE1-1 digipeater +//#define _DIGI_ONLY_789 // Limit digipeater to handle only -7, -8 and -9 SSIDs +//#define _VICTRON // Enable support for Victron VE.Direct protocol + + +/* MODES OF OPERATION */ +/* ------------------ */ + +//#define PARATNC_HWREV_A +//#define PARATNC_HWREV_B +//#define PARATNC_HWREV_C +#define PARAMETEO + +/* ---------------------------- */ +/* WEATHER/METEO CONFIGURATION */ + + + +// If none of those three sources are chosen (uncommented) the software will use internal sensors + +//#define _UMB_MASTER +//#define _DAVIS_SERIAL +#define _MODBUS_RTU // use Modbus RTU slave devices as a external meteo data source. For more configuration + // (slave ids, registers...) please look into MODBUS RTU CONFIGURATION section of this file + +#define _INTERNAL_AS_BACKUP // if defined ParaTNC will switch to internal sensors in case of + // the communication with UMB/Dallas Serial/Modbus external sensors will hang up + + +//#define _DALLAS_AS_TELEM // Use Dallas one-wire thermometer as a 5th telemetry channel + // May be used even if _METEO is not enabled +#define _DALLAS_SPLIT_PIN // Must be enabled for all ParaTNC hardware revisions + + +/******** INTERNAL SENSORS CONFIGURATION *****************/ + +//#define _ANEMOMETER_TX20 // Use TX20 as an internal anemometer +#define _ANEMOMETER_ANALOGUE // Use analogue/mechanical (like Davis 6410) as an internal anemometr +#define _ANEMOMETER_PULSES_IN_10SEC_PER_ONE_MS_OF_WINDSPEED 10 + +//#define _SENSOR_MS5611 +#define _SENSOR_BME280 + +#define _UMB_SLAVE_ID 1 +#define _UMB_SLAVE_CLASS 8 +#define _UMB_CHANNEL_WINDSPEED 460 +#define _UMB_CHANNEL_WINDGUSTS 440 +#define _UMB_CHANNEL_WINDDIRECTION 580 +#define _UMB_CHANNEL_TEMPERATURE 100 +#define _UMB_CHANNEL_QFE 300 + +/******** INTERNAL SENSORS CONFIGURATION *****************/ + +/*************** DATA SOURCES CONFIG ***********************/ +//#define _TEMPERATURE_INTERNAL +//#define _TEMPERATURE_UMB +//#define _TEMPERATURE_RTU +//#define _TEMPERATURE_DAVIS +// +//#define _PRESSURE_INTERNAL +//#define _PRESSURE_UMB +//#define _PRESSURE_RTU +//#define _PRESSURE_DAVIS +// +//#define _HUMIDITY_INTERNAL +//#define _HUMIDITY_UMB +//#define _HUMIDITY_RTU +//#define _HUMIDITY_DAVIS +// +// +//#define _WIND_INTERNAL +//#define _WIND_UMB +//#define _WIND_RTU +//#define _WIND_FULL_RTU +//#define _WIND_DAVIS +/*************** DATA SOURCES CONFIG ***********************/ + + +/* WEATHER/METEO CONFIGURATION */ +/* ---------------------------- */ + +//#define _MUTE_RF // TODO: Not yet implemented - This will make station RXonly and disable all data transmission +//#define _MUTE_OWN // TODO: Not yet implemented - This will disable all self-generated packets (wx, telemetry, beacon) + // and switch device to "pure" kiss TNC operation. Packets from PC will be transmitted normally. + +// Coordines should be in APRS decimal format DDDMM.SS for Longitude and DDMM.SS for latitude +#define _CALL "SP8EBC" +#define _SSID 1 +#define _LAT 4948.82 +#define _LATNS 'N' +#define _LON 01903.50 +#define _LONWE 'E' +#define _COMMENT "Set Your configuration in this file and rename to station_config.h" + +// You can use only one of these below defines to choose symbol. Meteo data are are always transmitted with blue WX symbol +//#define _SYMBOL_DIGI // uncomment if you want digi symbol(green star with D inside) +#define _SYMBOL_WIDE1_DIGI // uncomment if you want 'little' digi symbol (green star with digit 1 overlaid) +//#define _SYMBOL_HOUSE // uncomment if you want house symbol +//#define _SYMBOL_RXIGATE // uncomment if you want rxigate symbol (black diamond with R) +//#define _SYMBOL_IGATE // uncomment if you want igate symol (black diamond with I) + +// Or you can keep commented all symbol defines and choose custom one based on data from APRS symbols table +//#define _SYMBOL_F '/' +//#define _SYMBOL_S '#' + +// Uncomment one of these two defines to choose what path You want. If you uncommend both of them or +// if you keep both commended path will be completely disabled. CALL-S>AKLPRZ:data +#define _WIDE1_PATH // CALL-S>AKLPRZ,WIDE1-1:data +//#define _WIDE21_PATH // CALL-S>AKLPRZ,WIDE2-1:data + +// Comment this to disable beacon auto sending during startup (this can be risky if RF feedback occur) +//#define _BCN_ON_STARTUP + +#define _WX_INTERVAL 4 // WX packet interval in minutes +#define _BCN_INTERVAL 45 // Own beacon interval in minutes + +#define _PTT_PUSHPULL // Uncomment this if you want PTT line to work as Push-pull instead of Open Drain +#define _SERIAL_BAUDRATE 9600 + +// Transmitting delay +#define _DELAY_BASE 20 // * 50ms. For example setting 10 gives 500msec delay. Maximum value is 20 +//#define _RANDOM_DELAY // adds random delay TO fixed time set by _DELAY_BASE. This additional time can be + // from 100ms up to 1 sec in 100ms steps. Values are drawn from samples going from ADC + // so it is better to use Unsquelched output in radio to provide much more randomness +//After waiting time declared above ParaTNC will check DCD (Data Carrier Detect) flag, which works as some +//kind of semaphore. If radio channel is not occupied by any other transmission TX will be keyed up immediately, +//otherwise software will wait for clear conditions. + +// Few IMPORTANT hints about setting transmit delay properly. +// +// Transmit delay is key parameter to maintain RF network free from packet losses and collisions. If your station will be +// installed on tall object, without any other digi's close to it, you can set _DELAY_BASE to very low value and disable +// _RANDOM_DELAY. If you wanna rather auxiliary station, witch should only fill gap in RF coverage in small area, then +// _DELAY_BASE parameter should be not less than 12 (600msec), the smallest range the higher _DELAY_BASE should be. +// Additionally for gapfillers (auxiliary stations) _RANDOM_DELAY schould be enabled. +// +// This delay will ensure that while other station will be transmitting repeated packets from mobile, Yours will keep +// always quiet and won't jam RF network. This greatly improve DCD based access to channel. Various controllers uses +// various lenght of preamble, some of them produce signal which might be impossible to decode by ParaTNC, so DCD +// is only one part of effective multiaccess to medium. + +/* ---------------------------- */ +/* MODBUS RTU CONFIGURATION */ + +// scaling coefficients are used as follows +// +// A * x ^ 2 + B * x + C +// real value = --------------------------- +// D +// +// because of that D cannot be set to zero +#define _RTU_SLAVE_SPEED 9600u +#define _RTU_SLAVE_PARITY 0 +#define _RTU_SLAVE_STOP_BITS 2 + +#define _RTU_SLAVE_ID_1 0x01 +#define _RTU_SLAVE_FUNC_1 0x03 +#define _RTU_SLAVE_ADDR_1 0x00 +#define _RTU_SLAVE_LENGHT_1 0x01 +#define _RTU_SLAVE_SCALING_A_1 0 +#define _RTU_SLAVE_SCALING_B_1 1 +#define _RTU_SLAVE_SCALING_C_1 0 +#define _RTU_SLAVE_SCALING_D_1 10 + +#define _RTU_SLAVE_ID_2 0x01 +#define _RTU_SLAVE_FUNC_2 0x03 +#define _RTU_SLAVE_ADDR_2 0x01 +//#define _RTU_SLAVE_LENGHT_2 0x01 +#define _RTU_SLAVE_SCALING_A_2 0 +#define _RTU_SLAVE_SCALING_B_2 1 +#define _RTU_SLAVE_SCALING_C_2 0 +#define _RTU_SLAVE_SCALING_D_2 1 + +#define _RTU_SLAVE_ID_3 0x01 +#define _RTU_SLAVE_FUNC_3 0x03 +#define _RTU_SLAVE_ADDR_3 0x02 +//#define _RTU_SLAVE_LENGHT_3 0x01 +#define _RTU_SLAVE_SCALING_A_3 0 +#define _RTU_SLAVE_SCALING_B_3 1 +#define _RTU_SLAVE_SCALING_C_3 0 +#define _RTU_SLAVE_SCALING_D_3 1 + +#define _RTU_SLAVE_ID_4 0x01 +#define _RTU_SLAVE_FUNC_4 0x03 +#define _RTU_SLAVE_ADDR_4 0x03 +//#define _RTU_SLAVE_LENGHT_4 0x01 +#define _RTU_SLAVE_SCALING_A_4 0 +#define _RTU_SLAVE_SCALING_B_4 1 +#define _RTU_SLAVE_SCALING_C_4 0 +#define _RTU_SLAVE_SCALING_D_4 1 + +#define _RTU_SLAVE_ID_5 0x00 +#define _RTU_SLAVE_FUNC_5 0x00 +#define _RTU_SLAVE_ADDR_5 0x03 +//#define _RTU_SLAVE_LENGHT_4 0x01 +#define _RTU_SLAVE_SCALING_A_5 0 +#define _RTU_SLAVE_SCALING_B_5 1 +#define _RTU_SLAVE_SCALING_C_5 0 +#define _RTU_SLAVE_SCALING_D_5 1 + + +#define _RTU_SLAVE_ID_6 0x00 +#define _RTU_SLAVE_FUNC_6 0x00 +#define _RTU_SLAVE_ADDR_6 0x00 +//#define _RTU_SLAVE_LENGHT_4 0x01 +#define _RTU_SLAVE_SCALING_A_6 0 +#define _RTU_SLAVE_SCALING_B_6 1 +#define _RTU_SLAVE_SCALING_C_6 0 +#define _RTU_SLAVE_SCALING_D_6 1 + +//#define _RTU_SLAVE_TEMPERATURE_SOURCE 1 +#define _RTU_SLAVE_HUMIDITY_SOURCE 2 +//#define _RTU_SLAVE_PRESSURE_SOURCE 3 +//#define _RTU_SLAVE_WIND_DIRECTION_SORUCE 4 +//#define _RTU_SLAVE_WIND_SPEED_SOURCE 4 + + +/* MODBUS RTU CONFIGURATION */ +/* ---------------------------- */ + +// Do not touch this +#if defined (_SYMBOL_DIGI) && !defined (_SYMBOL_WIDE1_DIGI) && !defined (_SYMBOL_HOUSE) && !defined (_SYMOL_RXIGATE) &&\ + !defined (_SYMBOL_IGATE) +#define _SYMBOL_F '/' +#define _SYMBOL_S '#' +#elif !defined (_SYMBOL_DIGI) && defined (_SYMBOL_WIDE1_DIGI) && !defined (_SYMBOL_HOUSE) && !defined (_SYMOL_RXIGATE) &&\ + !defined (_SYMBOL_IGATE) +#define _SYMBOL_F '1' +#define _SYMBOL_S '#' +#elif !defined (_SYMBOL_DIGI) && !defined (_SYMBOL_WIDE1_DIGI) && defined (_SYMBOL_HOUSE) && !defined (_SYMOL_RXIGATE) &&\ + !defined (_SYMBOL_IGATE) +#define _SYMBOL_F '/' +#define _SYMBOL_S '-' +#elif !defined (_SYMBOL_DIGI) && !defined (_SYMBOL_WIDE1_DIGI) && !defined (_SYMBOL_HOUSE) && defined (_SYMOL_RXIGATE) &&\ + !defined (_SYMBOL_IGATE) +#define _SYMBOL_F 'I' +#define _SYMBOL_S '&' +#elif !defined (_SYMBOL_DIGI) && !defined (_SYMBOL_WIDE1_DIGI) && !defined (_SYMBOL_HOUSE) && !defined (_SYMOL_RXIGATE) &&\ + defined (_SYMBOL_IGATE) +#define _SYMBOL_F 'R' +#define _SYMBOL_S '&' +#elif !defined (_SYMBOL_F) && !defined (_SYMBOL_S) +#error "Missing symbol configuration in station_config.h" +#elif defined (_SYMBOL_F) && defined (_SYMBOL_S) +#else +#error "Wrong symbol configuration in station_config.h" +#endif +#if defined (_METEO) && !defined (_DIGI) +#define _DIGI +#endif + +#if defined(PARATNC_HWREV_A) && (defined (_METEO) || defined (_DALLAS_AS_TELEM)) && !defined(_DALLAS_SPLIT_PIN) +#define _DALLAS_SPLIT_PIN +#endif + +#if defined(PARATNC_HWREV_B) && (defined (_METEO) || defined (_DALLAS_AS_TELEM)) && !defined(_DALLAS_SPLIT_PIN) +#define _DALLAS_SPLIT_PIN +#endif + +#if defined(_ANEMOMETER_TX20) && defined(_ANEMOMETER_ANALOGUE) +#error "You cannot use two anemometers at once!!!" +#endif + +#if defined(_MOBUS_RTU) && defined(_DAVIS_SERIAL) +#error "You cannot use modbus RTU devices and Davis weather station at once!!!" +#endif + +#if !defined(_ANEMOMETER_TX20) && !defined(_ANEMOMETER_ANALOGUE) && !defined(_UMB_MASTER) && defined(_METEO) +#define _ANEMOMETER_TX20 +#endif + +#endif /* STATION_CONFIG_H_ */