OpenBuilds CONTROL

G54 G55 G56 G57 G58 G59	mm-mode inch-mode
	X WORK 0.000	Goto X0 (Work Coord) (G0 X0) Goto X0 (Machine Coord) (G53 G0 X0) Probe X-Zero Wizard Probe XYZ-Zero Wizard
	Y WORK 0.000	Goto Y0 (Work Coord) (G0 Y0) Goto Y0 (Machine Coord) (G53 G0 Y0) Probe Y-Zero Wizard Probe XYZ-Zero Wizard
	Z WORK 0.000	Goto Z0 (Work Coord) (G0 Z0) Goto Z0 (Machine Coord) (G53 G0 Z0) Probe Z-Zero Wizard Probe XYZ-Zero Wizard
	A WORK 0.000	Goto A0 (Work Coord) (G0 Z0) Goto A0 (Machine Coord) (G53 G0 A0)
	GOTOZERO (Work Coord) (G0 Z5, G0 X0 Y0, G0 Z0) (Retract Z to Work Coord Z5) GOTOZERO (Z Machine Coord, XY Work Coord) (G53 G0 Z0, G0 X0 Y0, G0 Z0) (Retract Z to Machine Coord) GOTOZERO (Machine Coord) (G53 G0 Z0, G53 G0 X0 Y0)	Go to Pre-Defined Position (G28) Go to Pre-Defined Position (G30) Set Pre-Defined Position (G28.1) Set Pre-Defined Position (G30.1)

Incremental Jog

app-notification

Continuous Jog

Inputs / Endstops

PIN	Status
Manually activate inputs you want to test
X-Limit	NOCOMM
Y-Limit	NOCOMM
Z-Limit	NOCOMM
Probe	NOCOMM
Door Sensor	NOCOMM
Buttons	NOCOMM NOCOMM NOCOMM

Power Settings

Setting	Status
We recommend USB Selective Suspend be Disabled to avoid USB issues
USB Selective Suspend on AC Power	NOCOMM
USB Selective Suspend on Battery Power	NOCOMM

Registration Settings

Parameter	Status
Registered To:	NOCOMM

Communications

Value	Status
Installed Version	NOCOMM
Backend Queue Blocked	NOCOMM
Connection Status	NOCOMM
Connected To	NOCOMM
Serial Queue	NOCOMM
Websocket Status	NOCOMM
Firmware	NOCOMM

Changelog

Not Connected

Job Queue: 0

Update Ready

OpenBuilds-CONTROL v1.0.100 has finished downloading and is ready to be installed!
Note that proceeding will:

Stop any running jobs
Shut down this instance of OpenBuilds CONTROL
Launch the installer for the new version

You may want to wait until your machine is idle, and it it's a convenient time for you to do this, before continuing

This release has already been downloaded several times since its release on

Jog Widget

You can use your mobile device as an handheld Jog interface. To get started, open a web-browser on your Mobile device and navigate to
http://0.0.0.0:3000/jog.html
or scan the QR Code below

Probing Wizard

Automatic Probe Routine: This routine is used to find the XYZ origins, as well as automatically determine endmill diameter.

Position the endmill above the hole in the probe plate as shown, just above the plate, clip the magnet to the collet, then click the Confirm Probe Position button to continue...

XYZ Probe Routine: This routine is used to find the XYZ origins

Position the endmill above the hole in the probe plate as shown, just above the plate, clip the magnet to the collet, then click the Confirm Probe Position button to continue...

X Probe Routine: This routine is used to find the X origin

Position the endmill to the left of the probe plate as shown, clip the magnet to the collet, then click the Confirm Probe Position button to continue...

Y Probe Routine: This routine is used to find the Y origin

Position the endmill in front of the probe plate as shown, clip the magnet to the collet, then click the Confirm Probe Position button to continue...

Z Probe Routine: This routine is used to find the Z origin

Position the endmill above the probe plate as shown, clip the magnet to the collet or the alligator clip to the bit, then click the Confirm Probe Position button to continue...

Endmill Probe Routine: This routine is used to find the Endmill Diameter

Position the endmill above the hole in the probe plate as shown, just above the plate, clip the magnet to the collet, then click the Confirm Probe Position button to continue...

This operation will perform an XYZ probe to establish the plate position, then using the hole in the plate, it will measure and calculate the Endmill Diameter and display it onscreen.
This operation will NOT set any work-coordinates!



Or use the Keyboard to Jog

Endmill Diameter

Plate Thickness

Where is the XY Zero Datum / Origin in your CAM setup, relative to the front-left corner we are probing?

If the origin is not Front, Left (Default): Then provide stock dimensions to calculate correct offset of X0, Y0:
Width Length

Probe Type:

OpenBuilds XYZ Probe Plus

Edit Custom Probe

Completed

Saving Grbl Settings

Writing changed parameters to controller:

Parameter	New Value

OpenBuilds® CONTROL

OpenBuilds^® CONTROL