kopia lustrzana https://github.com/lightaprs/LightAPRS-W-1.0
126 wiersze
3.8 KiB
C++
Executable File
126 wiersze
3.8 KiB
C++
Executable File
/*
|
|
* si5351_calibration.ino - Simple calibration routine for the Si5351
|
|
* breakout board.
|
|
*
|
|
* Copyright 2015 - 2018 Paul Warren <pwarren@pwarren.id.au>
|
|
* Jason Milldrum <milldrum@gmail.com>
|
|
*
|
|
* Uses code from https://github.com/darksidelemm/open_radio_miniconf_2015
|
|
* and the old version of the calibration sketch
|
|
*
|
|
* This sketch is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
* Foobar is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
* You should have received a copy of the GNU General Public License.
|
|
* If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include "si5351.h"
|
|
#include "Wire.h"
|
|
|
|
Si5351 si5351;
|
|
|
|
int32_t cal_factor = 0;
|
|
int32_t old_cal = 0;
|
|
|
|
uint64_t rx_freq;
|
|
uint64_t target_freq = 1000000000ULL; // 10 MHz, in hundredths of hertz
|
|
|
|
void setup()
|
|
{
|
|
// Start serial and initialize the Si5351
|
|
Serial.begin(57600);
|
|
|
|
// The crystal load value needs to match in order to have an accurate calibration
|
|
si5351.init(SI5351_CRYSTAL_LOAD_8PF, 0, 0);
|
|
|
|
// Start on target frequency
|
|
si5351.set_correction(cal_factor, SI5351_PLL_INPUT_XO);
|
|
si5351.set_pll(SI5351_PLL_FIXED, SI5351_PLLA);
|
|
si5351.set_freq(target_freq, SI5351_CLK0);
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
si5351.update_status();
|
|
if (si5351.dev_status.SYS_INIT == 1)
|
|
{
|
|
Serial.println(F("Initialising Si5351, you shouldn't see many of these!"));
|
|
delay(500);
|
|
}
|
|
else
|
|
{
|
|
Serial.println();
|
|
Serial.println(F("Adjust until your frequency counter reads as close to 10 MHz as possible."));
|
|
Serial.println(F("Press 'q' when complete."));
|
|
vfo_interface();
|
|
}
|
|
}
|
|
|
|
static void flush_input(void)
|
|
{
|
|
while (Serial.available() > 0)
|
|
Serial.read();
|
|
}
|
|
|
|
static void vfo_interface(void)
|
|
{
|
|
rx_freq = target_freq;
|
|
cal_factor = old_cal;
|
|
Serial.println(F(" Up: r t y u i o p"));
|
|
Serial.println(F(" Down: f g h j k l ;"));
|
|
Serial.println(F(" Hz: 0.01 0.1 1 10 100 1K 10k"));
|
|
while (1)
|
|
{
|
|
if (Serial.available() > 0)
|
|
{
|
|
char c = Serial.read();
|
|
switch (c)
|
|
{
|
|
case 'q':
|
|
flush_input();
|
|
Serial.println();
|
|
Serial.print(F("Calibration factor is "));
|
|
Serial.println(cal_factor);
|
|
Serial.println(F("Setting calibration factor"));
|
|
si5351.set_correction(cal_factor, SI5351_PLL_INPUT_XO);
|
|
si5351.set_pll(SI5351_PLL_FIXED, SI5351_PLLA);
|
|
Serial.println(F("Resetting target frequency"));
|
|
si5351.set_freq(target_freq, SI5351_CLK0);
|
|
old_cal = cal_factor;
|
|
return;
|
|
case 'r': rx_freq += 1; break;
|
|
case 'f': rx_freq -= 1; break;
|
|
case 't': rx_freq += 10; break;
|
|
case 'g': rx_freq -= 10; break;
|
|
case 'y': rx_freq += 100; break;
|
|
case 'h': rx_freq -= 100; break;
|
|
case 'u': rx_freq += 1000; break;
|
|
case 'j': rx_freq -= 1000; break;
|
|
case 'i': rx_freq += 10000; break;
|
|
case 'k': rx_freq -= 10000; break;
|
|
case 'o': rx_freq += 100000; break;
|
|
case 'l': rx_freq -= 100000; break;
|
|
case 'p': rx_freq += 1000000; break;
|
|
case ';': rx_freq -= 1000000; break;
|
|
default:
|
|
// Do nothing
|
|
continue;
|
|
}
|
|
|
|
cal_factor = (int32_t)(target_freq - rx_freq) + old_cal;
|
|
si5351.set_correction(cal_factor, SI5351_PLL_INPUT_XO);
|
|
si5351.set_pll(SI5351_PLL_FIXED, SI5351_PLLA);
|
|
si5351.pll_reset(SI5351_PLLA);
|
|
si5351.set_freq(target_freq, SI5351_CLK0);
|
|
Serial.print(F("Current difference:"));
|
|
Serial.println(cal_factor);
|
|
}
|
|
}
|
|
}
|