Hamlib/uniden/pro2052.c

158 wiersze
4.5 KiB
C

/*
* Hamlib Uniden backend - Radio Shack PRO-2052 description
* Copyright (c) 2001-2008 by Stephane Fillod
*
* $Id: pro2052.c,v 1.1 2008-05-04 14:23:54 fillods Exp $
*
* This library is free software; you can redistribute it and/or modify
* it under the terms of the GNU Library General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU Library General Public License for more details.
*
* You should have received a copy of the GNU Library General Public
* License along with this library; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
*/
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif
#include <stdlib.h>
#include <hamlib/rig.h>
#include "uniden.h"
#define PRO2052_MODES (RIG_MODE_AM|RIG_MODE_FM|RIG_MODE_WFM)
#define PRO2052_FUNC (RIG_FUNC_MUTE)
#define PRO2052_LEVEL_ALL (RIG_LEVEL_NONE)
#define PRO2052_PARM_ALL (RIG_PARM_NONE)
#define PRO2052_VFO RIG_VFO_A
#define PRO2052_CHANNEL_CAPS \
UNIDEN_CHANNEL_CAPS
/*
* PRO-2052 rig capabilities.
*
* From http://www.cantonmaine.com/pro2052.htm:
* After connecting the cable, turn on the computer and the scanner and then
* press and hold the Remote/Hold button on the scanner until you see "SFT"
* flashing on the right side of the LCD. You should now be communicating
* with the scanner. If it doesn't work, check all the normal stuff for
* whatever it was you overlooked. NOTE: You can change the scanner's
* default * baud rate by holding down the Remote/Hold button while turning
* on the scanner.)
*
* TODO: check this with manual or web site.
*/
const struct rig_caps pro2052_caps = {
.rig_model = RIG_MODEL_PRO2052,
.model_name = "PRO-2052",
.mfg_name = "Radio Shack",
.version = BACKEND_VER,
.copyright = "LGPL",
.status = RIG_STATUS_UNTESTED,
.rig_type = RIG_TYPE_TRUNKSCANNER,
.ptt_type = RIG_PTT_NONE,
.dcd_type = RIG_DCD_RIG,
.port_type = RIG_PORT_SERIAL,
.serial_rate_min = 2400,
.serial_rate_max = 19200,
.serial_data_bits = 8,
.serial_stop_bits = 1,
.serial_parity = RIG_PARITY_NONE,
.serial_handshake = RIG_HANDSHAKE_NONE,
.write_delay = 0,
.post_write_delay = 1,
.timeout = 200,
.retry = 3,
.has_get_func = PRO2052_FUNC,
.has_set_func = PRO2052_FUNC,
.has_get_level = PRO2052_LEVEL_ALL,
.has_set_level = RIG_LEVEL_SET(PRO2052_LEVEL_ALL),
.has_get_parm = PRO2052_PARM_ALL,
.has_set_parm = RIG_PARM_SET(PRO2052_PARM_ALL),
.level_gran = {}, /* FIXME: granularity */
.parm_gran = {},
.ctcss_list = NULL, /* FIXME: CTCSS list? */
.dcs_list = NULL,
.preamp = { RIG_DBLST_END },
.attenuator = { RIG_DBLST_END },
.max_rit = Hz(0),
.max_xit = Hz(0),
.max_ifshift = Hz(0),
.targetable_vfo = 0,
.transceive = RIG_TRN_OFF,
.bank_qty = 10, /* A..J */
.chan_desc_sz = 0,
.chan_list = {
{ 0, 999, RIG_MTYPE_MEM, {PRO2052_CHANNEL_CAPS} },
RIG_CHAN_END,
},
.rx_range_list1 = { RIG_FRNG_END, }, /* FIXME: enter region 1 setting */
.tx_range_list1 = { RIG_FRNG_END, },
.rx_range_list2 = {
{MHz(29),MHz(54),PRO2052_MODES,-1,-1,PRO2052_VFO},
{MHz(108),MHz(174),PRO2052_MODES,-1,-1,PRO2052_VFO},
{MHz(179.75),MHz(512),PRO2052_MODES,-1,-1,PRO2052_VFO},
{MHz(806),MHz(823.9375),PRO2052_MODES,-1,-1,PRO2052_VFO},
{MHz(851),MHz(868.9875),PRO2052_MODES,-1,-1,PRO2052_VFO},
{MHz(896.1125),MHz(956),PRO2052_MODES,-1,-1,PRO2052_VFO},
{MHz(1240),MHz(1300),PRO2052_MODES,-1,-1,PRO2052_VFO},
RIG_FRNG_END,
},
.tx_range_list2 = { RIG_FRNG_END, },
.tuning_steps = {
{PRO2052_MODES,kHz(5)},
{PRO2052_MODES,kHz(7.5)},
{PRO2052_MODES,kHz(10)},
{PRO2052_MODES,kHz(12.5)},
{PRO2052_MODES,kHz(25)},
{PRO2052_MODES,kHz(50)},
RIG_TS_END,
},
/* mode/filter list, remember: order matters! */
.filters = {
{RIG_MODE_AM|RIG_MODE_FM, kHz(8)},
{RIG_MODE_WFM, kHz(230)},
RIG_FLT_END,
},
.priv = NULL,
.set_freq = uniden_set_freq,
.get_freq = uniden_get_freq,
.set_mode = uniden_set_mode,
.get_mode = uniden_get_mode,
.set_mem = uniden_set_mem,
.get_mem = uniden_get_mem,
.get_dcd = uniden_get_dcd,
.get_info = uniden_get_info,
.get_level = uniden_get_level,
.set_level = uniden_set_level,
.get_channel = uniden_get_channel,
.set_channel = uniden_set_channel,
};
/*
* Function definitions below
*/