Hamlib/tentec/rx350.c

153 wiersze
3.6 KiB
C

/*
* Hamlib TenTenc backend - RX-350 description
* Copyright (c) 2003-2004 by Stephane Fillod
*
*
* This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU Lesser General Public
* License as published by the Free Software Foundation; either
* version 2.1 of the License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* Lesser General Public License for more details.
*
* You should have received a copy of the GNU Lesser General Public
* License along with this library; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
*
*/
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif
#include <stdlib.h>
#include <hamlib/rig.h>
#include "tentec2.h"
#include "bandplan.h"
#define RX350_MODES (RIG_MODE_FM|RIG_MODE_CW|RIG_MODE_SSB|\
RIG_MODE_AM|RIG_MODE_AMS)
#define RX350_FUNCS (RIG_FUNC_NR|RIG_FUNC_ANF)
#define RX350_LEVELS (RIG_LEVEL_RAWSTR|/*RIG_LEVEL_NB|*/ \
RIG_LEVEL_RF|RIG_LEVEL_IF| \
RIG_LEVEL_AF|RIG_LEVEL_AGC| \
RIG_LEVEL_SQL|RIG_LEVEL_ATT)
#define RX350_ANTS (RIG_ANT_1)
#define RX350_PARMS (RIG_PARM_TIME)
#define RX350_VFO (RIG_VFO_A|RIG_VFO_B)
#define RX350_VFO_OPS (RIG_OP_TO_VFO|RIG_OP_FROM_VFO)
/*
* RX350 receiver capabilities.
*
* Protocol is documented at
* http://www.rfsquared.com/
*
* Only set_freq is supposed to work.
* This is a skelton.
*/
const struct rig_caps rx350_caps = {
.rig_model = RIG_MODEL_RX350,
.model_name = "RX-350",
.mfg_name = "Ten-Tec",
.version = "0.1",
.copyright = "LGPL",
.status = RIG_STATUS_UNTESTED,
.rig_type = RIG_TYPE_RECEIVER,
.ptt_type = RIG_PTT_NONE,
.dcd_type = RIG_DCD_NONE,
.port_type = RIG_PORT_SERIAL,
.serial_rate_min = 57600,
.serial_rate_max = 57600,
.serial_data_bits = 8,
.serial_stop_bits = 1,
.serial_parity = RIG_PARITY_NONE,
.serial_handshake = RIG_HANDSHAKE_HARDWARE,
.write_delay = 0,
.post_write_delay = 0,
.timeout = 400,
.retry = 3,
.has_get_func = RX350_FUNCS,
.has_set_func = RX350_FUNCS,
.has_get_level = RX350_LEVELS,
.has_set_level = RIG_LEVEL_SET(RX350_LEVELS),
.has_get_parm = RX350_PARMS,
.has_set_parm = RX350_PARMS,
.level_gran = {}, /* FIXME: granularity */
.parm_gran = {},
.ctcss_list = NULL,
.dcs_list = NULL,
.preamp = { RIG_DBLST_END },
.attenuator = { 20, RIG_DBLST_END },
.max_rit = Hz(0),
.max_xit = Hz(0),
.max_ifshift = kHz(2),
.targetable_vfo = RIG_TARGETABLE_FREQ|RIG_TARGETABLE_MODE,
.transceive = RIG_TRN_OFF,
.bank_qty = 8,
.chan_desc_sz = 15,
.chan_list = {
{ 0, 127, RIG_MTYPE_MEM, TT_MEM_CAP },
},
.rx_range_list1 = {
{kHz(100),MHz(30),RX350_MODES,-1,-1,RX350_VFO,RX350_ANTS},
RIG_FRNG_END,
},
.tx_range_list1 = {
RIG_FRNG_END,
},
.rx_range_list2 = {
{kHz(100),MHz(30),RX350_MODES,-1,-1,RX350_VFO,RX350_ANTS},
RIG_FRNG_END,
},
.tx_range_list2 = {
RIG_FRNG_END,
},
.tuning_steps = {
{RX350_MODES,1},
RIG_TS_END,
},
/* mode/filter list, remember: order matters! */
.filters = {
{RX350_MODES, kHz(2.4)},
{RX350_MODES, 300},
{RX350_MODES, kHz(8)},
{RX350_MODES, 0}, /* 34 filters */
RIG_FLT_END,
},
.priv = (void*)NULL,
.set_freq = tentec2_set_freq,
.get_freq = tentec2_get_freq,
.set_vfo = tentec2_set_vfo,
.get_vfo = tentec2_get_vfo,
.set_mode = tentec2_set_mode,
.get_mode = tentec2_get_mode,
.reset = tentec2_reset,
.get_info = tentec2_get_info,
};
/*
* Function definitions below
*/