Add IC375

rigs/icom/ic275.c

@@ -46,6 +46,14 @@ static const struct icom_priv_caps ic275_priv_caps =
     ic737_ts_sc_list
 };
 
+static const struct icom_priv_caps ic375_priv_caps =
+{
+    0x12,   /* default address */
+    0,      /* 731 mode */
+    0,    /* no XCHG */
+    ic737_ts_sc_list
+};
+
 const struct rig_caps ic275_caps =
 {
     RIG_MODEL(RIG_MODEL_IC275),
@@ -145,3 +153,101 @@ const struct rig_caps ic275_caps =
     .hamlib_check_rig_caps = HAMLIB_CHECK_RIG_CAPS
 };
 
+const struct rig_caps ic375_caps =
+{
+    RIG_MODEL(RIG_MODEL_IC375),
+    .model_name = "IC-375",
+    .mfg_name =  "Icom",
+    .version =  BACKEND_VER ".0",
+    .copyright =  "LGPL",
+    .status =  RIG_STATUS_BETA,
+    .rig_type =  RIG_TYPE_TRANSCEIVER,
+    .ptt_type =  RIG_PTT_NONE,
+    .dcd_type =  RIG_DCD_NONE,
+    .port_type =  RIG_PORT_SERIAL,
+    .serial_rate_min =  300,
+    .serial_rate_max =  9600,
+    .serial_data_bits =  8,
+    .serial_stop_bits =  1,
+    .serial_parity =  RIG_PARITY_NONE,
+    .serial_handshake =  RIG_HANDSHAKE_NONE,
+    .write_delay =  0,
+    .post_write_delay =  0,
+    .timeout =  1000,
+    .retry =  3,
+    .has_get_func =  RIG_FUNC_NONE,
+    .has_set_func =  RIG_FUNC_NONE,
+    .has_get_level =  RIG_LEVEL_NONE,
+    .has_set_level =  RIG_LEVEL_NONE,
+    .has_get_parm =  RIG_PARM_NONE,
+    .has_set_parm =  RIG_PARM_NONE,
+    .level_gran =  {},
+    .parm_gran =  {},
+    .ctcss_list =  NULL,
+    .dcs_list =  NULL,
+    .preamp =   { RIG_DBLST_END, },
+    .attenuator =   { RIG_DBLST_END, },
+    .max_rit =  Hz(0),
+    .max_xit =  Hz(0),
+    .max_ifshift =  Hz(0),
+    .targetable_vfo =  0,
+    .vfo_ops =  IC275_VFO_OPS,
+    .scan_ops =  RIG_SCAN_NONE,
+    .transceive =  RIG_TRN_RIG,
+    .bank_qty =   0,
+    .chan_desc_sz =  0,
+
+    .chan_list =  {
+        {   1,  99, RIG_MTYPE_MEM, IC_MIN_MEM_CAP  },
+        { 100, 101, RIG_MTYPE_EDGE, IC_MIN_MEM_CAP },
+        { 102, 102, RIG_MTYPE_CALL, IC_MIN_MEM_CAP },
+        RIG_CHAN_END,
+    },
+
+    .rx_range_list1 =   { {MHz(138), MHz(174), IC275_MODES, -1, -1, IC275_VFO_ALL},
+        RIG_FRNG_END,
+    },
+    .tx_range_list1 =  { {MHz(144), MHz(146), IC275_MODES, W(2.5), W(25), IC275_VFO_ALL},
+        RIG_FRNG_END,
+    },
+
+    .rx_range_list2 =   { {MHz(138), MHz(174), IC275_MODES, -1, -1, IC275_VFO_ALL},
+        RIG_FRNG_END,
+    },
+    .tx_range_list2 =  { {MHz(144), MHz(148), IC275_MODES, W(2.5), W(25), IC275_VFO_ALL},
+        RIG_FRNG_END,
+    },
+
+    .tuning_steps =     {
+        {IC275_MODES, 10}, /* TBC: does this rig supports settin tuning step? */
+        RIG_TS_END,
+    },
+    /* mode/filter list, remember: order matters! */
+    .filters =  {
+        {RIG_MODE_SSB | RIG_MODE_CW, kHz(2.2)},
+        {RIG_MODE_FM, kHz(15)},
+        RIG_FLT_END,
+    },
+
+    .cfgparams =  icom_cfg_params,
+    .set_conf =  icom_set_conf,
+    .get_conf =  icom_get_conf,
+
+    .priv = (void *)& ic375_priv_caps,
+    .rig_init =   icom_init,
+    .rig_cleanup =   icom_cleanup,
+    .rig_open =  icom_rig_open,
+    .rig_close =  icom_rig_close,
+
+    .set_freq =  icom_set_freq,
+    .get_freq =  icom_get_freq,
+    .set_mode =  icom_set_mode,
+    .get_mode =  icom_get_mode,
+    .set_vfo =  icom_set_vfo,
+
+    .decode_event =  icom_decode_event,
+    .set_mem =  icom_set_mem,
+    .vfo_op =  icom_vfo_op,
+
+    .hamlib_check_rig_caps = HAMLIB_CHECK_RIG_CAPS
+};