F5OEO-tstools/accessunit_defns.h

/*
 * Datastructures for working with access units in H.264 elementary streams.
 *
 * ***** BEGIN LICENSE BLOCK *****
 * Version: MPL 1.1
 *
 * The contents of this file are subject to the Mozilla Public License Version
 * 1.1 (the "License"); you may not use this file except in compliance with
 * the License. You may obtain a copy of the License at
 * http://www.mozilla.org/MPL/
 *
 * Software distributed under the License is distributed on an "AS IS" basis,
 * WITHOUT WARRANTY OF ANY KIND, either express or implied. See the License
 * for the specific language governing rights and limitations under the
 * License.
 *
 * The Original Code is the MPEG TS, PS and ES tools.
 *
 * The Initial Developer of the Original Code is Amino Communications Ltd.
 * Portions created by the Initial Developer are Copyright (C) 2008
 * the Initial Developer. All Rights Reserved.
 *
 * Contributor(s):
 *   Amino Communications Ltd, Swavesey, Cambridge UK
 *
 * ***** END LICENSE BLOCK *****
 */

#ifndef _accessunit_defns
#define _accessunit_defns

#include "nalunit_defns.h"
#include "es_defns.h"

// Since reverse_data refers to h262 and acces_unit datastructures, and
// *they* refer to reverse_data, we need to break the circular referencing
// at some point
typedef struct access_unit_context *access_unit_context_p;
struct reverse_data;

// ------------------------------------------------------------
// A single access unit
struct access_unit
{
  uint32_t    index;       // The (notional) index of this unit in the stream
                           // (i.e., from the context's access_unit_index)
  int         started_primary_picture; // True if we have, indeed, done so
  nal_unit_p  primary_start;  // First NAL unit of our primary picture
                              // (a pointer into `nal_units`)

  // A "list" of the NAL units that form us
  // (the only reason we don't use an ES unit list is that I want to be
  // able to report on the content of an access unit in terms of the NAL
  // units that form it - perhaps more important in development than in
  // prodcution, but still)
  nal_unit_list_p  nal_units;

  // Did we ignore any "broken" NAL units when we were being built?
  // (if so, there's a case to say we might be broken too)
  int      ignored_broken_NAL_units;
  
  // Information derived from the slices in this access unit
  // (all slices in an access unit must have the same values for these,
  // so these could actually just be derived from the `primary_start`,
  // but it's slightly easier to have them more available, and saves
  // the need to check if `primary_start` is defined before using them).
  uint32_t frame_num;
  byte     field_pic_flag;    // frame or field?
  byte     bottom_field_flag; // for a field (only), bottom or top?
  // (After merging two field access units into a single frame,
  // `field_pic_flag` will be set to 0, to "pretend" that we have a
  // "proper" frame access unit)
};
typedef struct access_unit *access_unit_p;
#define SIZEOF_ACCESS_UNIT sizeof(struct access_unit)

// ------------------------------------------------------------
// Context for looping over the access units in an elementary stream
struct access_unit_context
{
  // ---------------------------------------------------------------
  // Public information - things it makes sense for users to inspect
  // ---------------------------------------------------------------
  nal_unit_context_p  nac;  // short and nasty "mnemonic"

  // If we read an EndOfStream or EndOfSequence NAL unit, then we
  // want to remember as much. We don't really want to put it into
  // the preceding access unit (for a start, that would mess up
  // reversing the stream), but we also don't want to forget it,
  // and in the case of EndOfStream, we don't want to carry on
  // reading the ES after finding it. The simplest thing is just
  // to remember them.
  nal_unit_p      end_of_sequence;
  nal_unit_p      end_of_stream;

  // We count all of the access units as we read them (this is useful
  // when we are building up reverse_data arrays). If functions
  // move around in the data stream, we assume that they will
  // (re)set this to a sensible value.
  // The index of the first access unit read is 1, and this value is
  // incremented by each call of `get_next_access_unit`
  uint32_t       access_unit_index;  // The index of the last access unit read

  // If we are collecting reversing information, then we keep a reference
  // to the reverse data here
  struct reverse_data * reverse_data;
  
  // -------------------------------------------------------------
  // Private information - used internally by the software, not to
  // be relied upon by outsiders
  // -------------------------------------------------------------
  // If we ended the previous access unit because of finding a NAL
  // unit that provokes a *new* access unit, then we remember it
  // (after all, we'll want to put it into the new access unit)
  nal_unit_p     pending_nal;
  // We need to remember the VCL NAL unit that started the previous
  // primary picture, so that we can compare a later VCL NAL unit
  // to it, to see if we've got a new primary picture starting
  // (actually, we'll only remember a "stub" of information for it)
  nal_unit_p      earlier_primary_start;
  // Some items go "in front of" the next VCL NAL unit, so we need
  // a list of such
  nal_unit_list_p pending_list;
  // If we read an end of stream NAL unit, then next time we try
  // to read an access unit, we want to know that there is no point.
  // Similarly, if we read EOF on the input stream.
  byte            no_more_data;
};
#define SIZEOF_ACCESS_UNIT_CONTEXT sizeof(struct access_unit_context)

#endif // _accessunit_defns

// Local Variables:
// tab-width: 8
// indent-tabs-mode: nil
// c-basic-offset: 2
// End:
// vim: set tabstop=8 shiftwidth=2 expandtab: